Page 2 of MC2102 Power Amplifier by McIntosh Laboratory, Inc.

mcintosh laboratory inc 2 chambers street binghamton new york 13903-2699 tel 607 723-3512 · us toll-free 800 538-6576 · fax 607 724-0549 · www.mcintoshlabs.com for the consumer s protection in order to ensure the highest level of customer satisfaction new mcintosh products may only be purchased over-the-counter or delivered and installed by an authorized mcintosh dealer mcintosh products that are purchased over the internet by phone or mail order are presumed to be used and do not qualify for any mcintosh warranty mcintosh does not warrant in any way products that are purchased from anyone who is not an authorized dealer or products that have had their serial number altered or defaced mc2102 vacuum tube power amplifier power output stereo minimum sine wave continuous average power output per channel all channels operating is 100 watts into 2 ohm load 100 watts into 4 ohm load 100 watts into 8 ohm load power output mono parallel minimum sine wave continuous average power output is 200 watts into 1 ohm 2 ohm or 4 ohm load power output mono bridge minimum sine wave continuous average power output is 200 watts into 4 ohm 8 ohm or 16 ohm load rated power band 20hz to 20khz total harmonic distortion 0.05 max at any power level from 250 milliwatts to rated power output is 0.5 for 2 4 or 8 ohm loads stereo 0.5 for 1 2 or 4 ohm loads mono parallel 0.5 for 4 8 or 16 ohm loads mono bridge frequency response 20hz to 20khz +0 -0.25db 10hz to 100khz +0 -3db sensitivity 2.5v unbalanced inputs 5.0v balanced inputs a-weighted signal-to-noise ratio 100db below rated output wide band damping factor greater than 18 output load impedance terminals for 2 4 or 8 ohms stereo terminals for 1 2 or 4 ohms mono parallel terminals for 4 8 or 16 ohms mono bridged intermodulation distortion smpte 0.5 maximum if instantaneous peak output does not exceed twice the output rating input impedance 20,000 ohms unbalanced 40,000 ohms balanced power requirements 120v 50/60hz 5.0a overall dimensions h xwxd including feet and knobs 10-1/8 25.72cm x 17-3/4 45.54cm x 17 43.18cm weight 88 lbs 40.87kg net 121lbs 54.9kg boxed unity coupling the mcintosh unity coupled output circuit with four output tubes kt88 per channel in a push-pull parallel configuration for high power of 100 watts per channel accurate meters the illuminated peak-responding meters display output power in watts response is almost 10 times faster than a vu meter high connectivity balanced input connectors guard against noise pick up and allow long input cable runs without compromising sound quality huge gold-plated output posts with connections for 2 4 and 8 ohms this ensures you get all the power you paid for with any type of loudspeakers mono-bridge and mono-parallel modes enable the mc2102 to deliver a full 200 watts as a mono amplifier into 1 2 4 8 or 16 ohm loads freedom from distortion low distortion is a hallmark of mcintosh tube amplifiers distortion remains under 0.5 thd and im over the complete range of 20-20khz designed by mcintosh co-founder sidney a corderman and the mcintosh engineering staff stereo 100 watts per channel 8/4/2 ohm mono parallel 200 watts per channel 4/2/1 ohms mono bridged 200 watts per channel 16/8/4 ohms air-pipe cooling at base for output tubes gold-plated input jacks gold-plated 200a multi-way output binding posts 08.05.mc2102.5k.jcp 35006900

[close]