Catalog: Midwest Fasteners Catalog | |
| DOUBLE POINTED (ARC) PIN FERRULE SIZE D* L CODE 10GA .135 AS REQUIRED F135 *Other diameters available upon request. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available upon Yield 50,000 psi (min.) request. Elongation 20% (in 2 inches) PLATING: Galvanized and Copper plating are available. Does not apply to Stainless. ANNEALING: Can be annealed where required. Can be annealed if required. APPLICATION: This ... | |
| STUDS (General Information) 7-1 MIDWEST FASTENERS GENERAL SPECIFICATIONS CAPACITOR DISCHARGE ARC MATERIAL: Standard in low carbon steel, 302/304/305 Standard in low carbon steel and 302/304/305 stainless, and 1100, 6061, and 5000 series stainless. Aluminum, monel, inconel, and other aluminum. Brass and other grades of grades of stainless steel are available. stainless steel are also available. PLATING: Copper plating is standard. Cadmium, Cadmium to ASTM-A 165 type TS, zinc to nickel, zinc, and other platings are ASTM-B 633 (formerly A 164) and other platings available. are available. Non-weldable ... | |
| STUDS (General Information) THE ARC STUD WELDING PROCESS 1. STUD AND CERAMIC FERRULE AGAINST THE WORK PLATE 2. STUD LIFTS AND ARC IS DRAWN 3. CONTROL TIMES OUT AND STUD PLUNGES INTO MOLTEN STEEL 4. METAL SOLIDIFIES AND WELD IS COMPLETED IN MILLISECONDS ARC Stud Welding involves the same basic principles and metallurgical aspects as any other arc welding procedure. The weld gun lifts the stud a short distance from the base metal and initiates a controlled electric arc from the power source which melts the end of the stud and a portion of the base metal. The ceramic ferrule contains the molten metal ... | |
| 8-4 STUDS (General Information) ARC STUD WELD FILLET ACCOMMODATION COUNTER BORE OR COUNTER SINK METHODS When an arc stud is welded, a fillet forms around its base with the fillet dimensions being closely controlled by the design of the ferrule used. Since the diameter of the fillet is generally larger than the diameter of the stud, some consideration is required in the design of mating parts. MIDWEST FASTENERS recommends a counter bore and counter sink method for this application. Dimensions will vary with studs and ferrules. Additional methods of accommodating fillet include over-sized clearance ... | |
| 8-5 STUDS (General Information) ARC STUD LOCATION TEMPLATE BUSHING DESIGN TEMPLATE METHOD This method of templating is recommended by MID- WEST FASTENERS for use with ferrules. The template is usually a steel plate 3/32 to 3/16 thick. Spacers are required to allow the gases to escape during the welding cycle. The ferrule can be held by a standard ferrule grip or where clearance is prohibitive a tube type set-up can be used. The recommended hole sizes on the template to locate the ferrules should equal the maximum outside diameter of the ferrule plus 1/32 . Holes may be drilled or bored at required ... | |
| 8-6 STUDS (General Information) ARC STUD LOCATION TEMPLATE BUSHING DESIGN ARC STUD WELD INSPECTION (VISUAL) The MIDWEST FASTENERS ARC stud weld can be visually inspected by observing the fillet at the base of the stud. The illustrations and comments below will assist you in visually judging the quality of the weld. GOOD WELD Full, even, shiny fillet all around stud. HOT WELD Very shiny, low profile fillet extending beyond outside of ferrule. COLD WELD Small, uneven, dull appearing fillet with fingers of metal extending through vents of ferrule. SHORT PLUNGE OR HANG-UP No fillet, no stud burn-off, ... | |
| STANDARD THREAD THREADS: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request. Maximum standard thread length is 3-7/8 . MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: ... | |
| ARC STUDS 8-10 FULL THREAD THREADS: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request. Maximum standard thread length is 3-7/8 . MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. ... | |
| ARC STUDS 8-11 FULL BASE THREADS: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request. Maximum standard thread length is 3-7/8 . MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. ... | |
| ARC STUDS 8-12 LONG REDUCED BASE THREADS: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request. Maximum standard thread length is 3-7/8 . MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer ... | |
| ARC STUDS 8-13 SHORT REDUCED BASE THREADS: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request. Maximum standard thread length is 3-7/8 . MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer ... | |
| ARC STUDS 8-14 NO THREAD TO ORDER OR SPECIFY, GIVE: 1. Product Code ......................... ......................... ....................... ARC NT 2. Diameter ......................... ......................... ......................... ................ D 3. Length ......................... ......................... ......................... ..................... L 4. Material................. ......................... ......................... ......................... .... THREADS: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request. Maximum standard ... | |
| BENT NO THREAD THREADS: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request. Maximum standard thread length is 3-7/8 . MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: ... | |
| ARC STUDS 8-16 TAPPED FULL BASE TAPS: Standard tap is UNC-2B, other taps are available. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper nickel, and zinc available upon customer request. FERRULES: Ferrules are component parts of studs. Not sold separately. TO ORDER OR ... | |
| ARC STUDS 8-17 TAPPED REDUCED BASE TAPS: Standard tap is UNC-2B, other taps are available. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: Ferrules are component parts of studs. Not sold separately. TO ORDER ... | |
| ARC STUDS 8-18 SHOULDER THREADED THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: Ferrules are component parts ... | |
| ARC STUDS 8-19 SHOULDER ANNULAR GROVE THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: Ferrules are component ... | |
| ARC STUDS 8-20 SHOULDER NO THREAD THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: Ferrules are component parts ... | |
| ARC STUDS 8-21 COLLAR THREADS: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request. Maximum standard thread length is 3-7/8 . MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: ... | |
| ARC STUDS 8-22 BENT-COLLAR THREADS: Standard thread is UNC-2A (Rolled when possible), other threads are available upon request. Maximum standard thread length is 3-7/8 . MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. ... | |
| ARC STUDS 8-23 ANNULAR RING (NAVY) THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. Conforms to: MIL-S-24149 Type: I Class: III MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer ... | |
| ARC STUDS 8-24 RECTANGULAR-PLAIN THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: Ferrules are component parts ... | |
| ARC STUDS 8-25 RECTANGULAR- T SLOTTED THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: Ferrules are component ... | |
| ARC STUDS 8-26 RECTANGULAR-WITH HOLE THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL STAINLESS STEEL C 0.23% max. P 0.04% max. AISI grade 302/304/305 std. Mn 0.90% max. S 0.05% max. Other grades available upon request. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Values for various grades available Yield 50,000 psi (min.) upon request. Elongation 20% (in 2 inches) PLATING: Plating is not standard. Does not apply to Stainless. Copper, nickel, and zinc available upon customer request. FERRULES: Ferrules are component ... | |
| ARC STUDS 8-27 KNURLED THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL C 0.23% max. P 0.04% max. Mn 0.90% max. S 0.05% max. MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Elongation 20% (in 2 inches) FERRULES: Ferrules are component parts of studs. Not sold separately. TO ORDER OR SPECIFY, GIVE: 1. Product Code ......................... ......................... ......................... ......................... ......................... ............ ARC KNRL 2. Diameter ......................... ......................... ... | |
| ARC STUDS 8-28 HEADED CONCRETE ANCHOR THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL AISI C1010 through C1020 MECHANICAL PROPERTIES: Tensile 55,000 psi (min.) Elongation 20% (in 2 inches) OTHER MATERIALS: Also available in stainless steel. SPECS: ALL MIDWEST FASTENERS ARC HCA studs meet AWS specifications. Test reports available upon request. FERRULES: Ferrules are component parts of studs. Not sold separately. Ferrule exterior dimensions are available upon request. *HEADED CONCRETE ANCHORS are available for welding to ... | |
| ARC STUDS 8-29 SHEAR CONNECTOR THREADS: Standard thread is UNC-2A (Rolled when possible), other threads available upon request. MATERIAL: LOW CARBON STEEL AISI C1015, C1018, or C1020 MECHANICAL PROPERTIES: Tensile 60,000 psi (min.) Yield 50,000 psi (min.) Elongation 20% (min.) Reduction of Area 50% (min.) SPECS: ALL MIDWEST FASTENERS ARC SC studs meet AWS, AASHTO, and ICBO specifications. Test reports available upon request. FERRULES: Ferrules are component parts of studs. Not sold separately. Ferrule exterior dimensions are available upon request. *SHEAR CONNECTORS: Available for welding to flat ... | |
