Catalog: Boston Hose Assembly
Company/Brand: Moreland Hose and Belting
coll o crimp operating procedures in Boston Hose Assembly by Moreland Hose and Belting
conditioning procedure hose ends the coll-o-crimp® system can be used to make original ... factory replacement ends as listed on pages 88-94 if the required hose end is ... not found our flareless hose end can be used by ... following the instructions on this page a new hose assembly can be ... boston weatherhead s hose end with the original equipment end configuration typical ... original equipment assembly typical assembly of ... a flareless hose end used with an old original equipment end configuration 75708e-758 ... replacement assemblies using original equipment tubing with boston ... straight area for the presetting operation deburr the tubing with an inner-outer ...
medium pressure air fuel grease oil truck and power steering lines ... and is easy to assemble brass material offers excellent resistance against corrosion ... 420-1 t-440-1 t-460 t-462 t-465-1 t-480 ordering information order individually by ... to current price list for availability of cataloged items configurations and ... 7/8-14 a 1.69 1.80 1.96 2.08 hose cut-off factor .69 .81 .94 1.06 hole dia .130 . ... `p 265 `p series hose ends 1 brass collar 2 brass insert female sae 45° swivel ... 229 `p male pipe or female pipe 265 `p assembly ... `p 265 `p series hose ends 1 push collar onto hose until bottomed 2 push insert ... into hose until step on insert or hex is flush with collar 3 check for ...
and is easy to assemble brass material offers excellent resistance against corrosion ... ends reference pages 139-141 ordering information order individually by ... to current price list for availability of cataloged items configurations and ... hose labeling information brass or steel adapter swivel nut hoseendsy ... brass insert x brass collar componentry 1 brass collar 2 brass ... insert male pipe or brass swivel insert with brass sae nut ... b.s insert with steel a.b.s swivel nut crimp collet flush with collar step hex flush ... with collar assembly instructions 1 push collar ... onto hose until bottomed 2 push insert into ... hose until step on insert or hex is flush with collar note swivel ...
refer to safety information regarding coll-o-crimp® hose hose fittings and assembly ... equipment compatibility on pages1-2 t-475-1 · portable air ... conditioning press this hand operated lightweight and easy to use air ... mounting this portable press is made of heavy duty construction for use with an ... sizes 6 #8 #10 and #12 that produce an oe style triple bubble crimp no electrical ... requirements necessary capacity crimps 2-braid dimension nylon barrier or ... reduced dia hose mounting bench or mount in vise weight 6 lbs reference ... pages 237 through 245 for coll-o-crimp tooling tooling packages and pumps ... refer to safety information regarding coll-o-crimp® crimping procedures on pages 210-213 t- ...
equipment t-475-1 crimping procedure description of terms the ... crimper can be operated with a 1/2 drive air impact wrench ... ratchet or breaker bar it takes approximately 100 ... foot pounds of torque to fully close the jaws and ... achieve a satisfactory crimp the crimper can be bench mounted using the flange ... and pipe nipple provided or it can be mounted in a bench vise to ... a bench top screw the pipe nipple and crimper to the flange plate impact wrench 1/2 ... do not exceed 100 psig air pressure on the impact wrench as damage to the ... wrench and the crimper may result caution do not continue ... are closed this can cause damage to the crimper caution care should be taken when ...
t-475-1 crimping procedure caution it is not necessary ... to over-tighten the screws always use the short hex key ... wrench provided in order to avoid damage die carrier the die ... become worn and produce unacceptable crimps with time to replace the color coded ... carriers simply push the die segment out of the back of the carrier reverse the ... key is not in the center segment of each half of the die set an irregular ... crimp will be formed increasing the ... probability of leakage caution never use dies without ... woodruff key engaged in the slot of the segment and holder to replace the ... a screwdriver and hammer to remove the old key replace the key using a drop of ...
equipment t-465-1 crimping procedure warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 clamp the crimper into a vise ... or mount to a work bench using the ... 2 remove pusher and insert proper size collet halves 3 select proper weatherhead® ... coll-o-crimp® hose and end fitting insert hose into ... important make sure hose is bottomed on end fitting 4 insert hose assembly from ... below between the collet halves align dimples on hose end with ...
equipment t-460 crimping procedure refer to safety information ... regarding coll-o-crimp® hose hose fittings and assembly ... equipment compatibility on pages 1-2 warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 slide pusher to back of ... machine and insert proper size collet halves note lubricate tapered cone seat ... with lubriplate grease or equivalent before any crimping is done ... 2 select proper weatherhead® coll-o-crimp® hose end fitting insert hose into end ...
t-462 crimping procedure equipment refer to safety ... information regarding coll-o-crimp® hose hose fittings and assembly ... equipment compatibility on pages 1-2 warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 slide pusher to back of ... machine and insert proper size collet halves note lubricate tapered cone seat ... with lubriplate grease or equivalent before any crimping is done ... 2 select proper weatherhead® coll-o-crimp® hose end fitting insert hose into end ...
portable t-480-hp crimping procedure equipment warning you must ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger pusher clip pump release valve ... pump reservoir 2 close release valve on pump note periodically lubricate die ... knob and tilt press as necessary insert one end of hose assembly from below the ... base plate and between the collet halves align knurl on end fitting with ... top of collet making sure that collet halves are evenly aligned 6 holding ...
equipment portable t-480-ah crimping procedure warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger pusher clip pump pressure valve ... knob and tilt press as necessary insert one end of hose assembly from below the ... base plate and between the collet halves align knurl on end fitting with ... top of collet making sure that collet halves are evenly aligned 5 holding ... position t-480-68 blue extension ring on top of collet 6 slide pusher forward ...
portable t-480-ta crimping procedure equipment warning you must ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger release position pressure ... 1 connect hose assembly to pump and crimper 2 attach air supply to pump 3 vent pump ... by opening vent screw 1-2 turns note periodically ... knob and tilt press as necessary insert one end of hose assembly from below the ... base plate and between the collet halves align knurl on end fitting with ...
equipment portable t-480-ep crimping procedure warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 connect hose assembly to pump ... and crimper check all connections to be sure they ... are tight and leak free 2 open the pump vent plug by turning it 1-2 ... knob and tilt press as necessary insert one end of hose assembly from below the ... base plate and between the collet halves align knurl on end fitting with ...
portable t-480 operating figure a insertion depth place hose ... ends on hose until hose is bottomed in collar to insure that hose is bottomed in ... collar mark the insertion depth on the hose before inserting it into the ... 3/32 1-3/32 equipment figure b coll-o-crimp® spacer ring typical spacer ring ... illustrating both sides of ring flat side w v counterbore side ... figure c nominal crimp diameter measurement measuring crimp ... diameters should be a part of the normal hose assembly procedure to ... insure a proper crimp diameter reading follow these steps 1 ... measure the diameter in the middle of crimped portion of the hose end 2 place the ...
equipment iiiiiiiiiiiiiiiiiiiii t-400 crimping procedure warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 place die ring t-400-8 on base ... stops 2 insert properly-sized matched collet halves in the die ring see chart on ... press 3 place the correct coll-o-crimp® hose end on hose be sure hose is ... hose assembly from below between the collet halves align the dimples on the hose ... end collar with the top of the collet when crimping 229 `p 265 `p or 338 `p ...
refer to safety information regarding coll-o-crimp® hose hose fittings and assembly ... equipment compatibility on pages 1-2 t-407-1 · production coll-o- ... crimp® press the t-407-1 production coll-o-crimp® as its name implies is at its best in ... the fast production of straight configuration hose end ... crimping taking advantage of the swiveling bracket which supports ... the crimper tooling can be put in place and the ... a 90° angle facilitating quick hose end crimping a crimp locator is included when set to ... position the crimp locator allows for a preset of the ... correct crimp location so hose assemblies can be ...
iiiiiiiiiiiiiiiiiiiiiii t-440 the coll-o-crimp® ii plus is ideal for factory high ... performance machine operations construction and mine locations this ... machine offers the capabilities of crimping all of the crimp style hose ends ... weatherhead offers with this coverage this heavy-duty ... crimper can handle all of your crimping needs capacity 3/16 i.d 1 fiber braid ... through 2 6 spiral hose for hoses other than 4 and 6 spiral conversion tooling ... refer to safety information regarding coll-o-crimp® hose hose fittings and assembly ... equipment compatibility on pages 1-2 t-440-1 · coll-o-crimp® ii ... plus press only t-440-n · coll-o-crimp® ii plus package includes one each of ...
t-420 t-440 crimping procedure equipment warning you must ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger procedure for h039 h350 h425 ... 440 used in example 2 place proper size coll-o-crimp® hose end on hose be sure hose is ... hose end 2a when making a hose assembly on the t-440-1 c-o-c® machine using a ... 47032e-632 on each end you must manually remove the ... spring loaded collet retainer ring in order for the hose end to fit through the ...
equipment t-420 t-440 crimping procedure procedure for rubber nylon ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger t-420 used in example 1 hold ... switch on as ram starts down rotate the ram ... return stops out from their in position release ... allowing enough clearance for insertion of required tooling 2 open pusher halves ... base plate cavity select proper size collet for hose type and size being crimped ...
chart warning proper selection of hose ends selection of the proper end ... application is essential to the proper operation and safe use of the hose and related ... inadequate attention to the selection of the end fittings for your application ... can result in leaking or the hose ends blowing off the hose ... leading to serious bodily injury or property damage in order to avoid ... serious bodily injury or property damage resulting from ... selection of the wrong end fitting you should ... information in this catalog warning coll-o-crimp® hose hose fittings and assembly ...
