Catalog: Boston Transfer Hose Products
Company/Brand: Moreland Hose and Belting
coll o crimp operating procedures in Boston Transfer Hose Products by Moreland Hose and Belting
wolf series hose couplings should only be used with authorized boston ... a new installation please refer to your coll-o-crimp® set-up and operating instructions for ... installation procedures refer to page 96 of this catalog for ... information after the initial setup of the coll-o-crimp® press and purging of ... for a faster cycle time when using other coll-o-crimp® tooling in order to ... easily accommodate the tooling and crimp the wolf series hose couplings rotate ... the stops to their outward position and proceed as follows 1 ... pump by pulling the activating lever or turning on the switch 2 during the ...
size material ca360 brass advantages one piece construction easy to assemble ... 420-1 t-440-1 t-460 t-462 t-465-1 t-480 ordering information order individually by ... catalog number to order replacement collar only use base number followed by coo ... to current price list for availability of cataloged items configurations and ... for 265 `p series hose ends 1 brass collar 2 brass insert assembly instructions ... for 265 `p series hose ends 1 push collar onto hose until bottomed 2 push insert ... into hose until step on insert or hex is flush with collar 3 check for ... bottoming by checking collar movement along insert hose is bottomed ...
t-465-1 crimping procedure equipment warning you must ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 clamp the crimper into a vise ... or mount to a work bench using the ... 2 remove pusher and insert proper size collet halves 3 select proper boston ... weatherhead® coll-o-crimp® hose and end fitting insert hose into ... important make sure hose is bottomed on end fitting equipment 4 insert hose ... assembly from below between the collet halves align dimples on hose end with ...
t-460 crimping procedure equipment refer to safety ... information regarding coll-o-crimp® hose hose fittings and assembly ... equipment compatibility on pages 1-2 warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 slide pusher to back of ... machine and insert proper size collet halves note lubricate tapered cone seat ... with lubriplate grease or equivalent before any crimping is done ... 2 select proper boston weatherhead® coll-o-crimp® hose end fitting insert hose into end ...
equipment t-462 crimping procedure refer to safety information ... regarding coll-o-crimp® hose hose fittings and assembly ... equipment compatibility on pages 1-2 warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 slide pusher to back of ... machine and insert proper size collet halves note lubricate tapered cone seat ... with lubriplate grease or equivalent before any crimping is done ... 2 select proper boston weatherhead® coll-o-crimp® hose end fitting insert hose into end ...
refer to safety information regarding coll-o-crimp® hose hose fittings and assembly ... equipment compatibility on pages 1-2 3 4 5 1 4 6 8 9 11 7 2 10 ... hand pump air/hydraulic pump set-up operating guide blue pusher extension ring 10,000 ... t-480-ah system for t-480 system see crimping procedure for instructions includes ...
equipment portable t-480-hp crimping procedure warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger pusher clip pump release valve ... pump reservoir 2 close release valve on pump note periodically lubricate die ... knob and tilt press as necessary insert one end of hose assembly from below the ... base plate and between the collet halves align knurl on end fitting with ... top of collet making sure that collet halves are evenly aligned 6 holding ...
portable t-480-ah crimping procedure equipment warning you must ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger pusher clip pump pressure valve ... knob and tilt press as necessary insert one end of hose assembly from below the ... base plate and between the collet halves align knurl on end fitting with ... top of collet making sure that collet halves are evenly aligned 5 holding ... position t-48068 blue extension ring on top of collet see note 6 slide pusher ...
equipment portable t-480-ta crimping procedure warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger release position pressure ... 1 connect hose assembly to pump and crimper 2 attach air supply to pump 3 vent pump ... by opening vent screw 1-2 turns note periodically ... knob and tilt press as necessary insert one end of hose assembly from below the ... base plate and between the collet halves align knurl on end fitting with ...
portable t-480-ep crimping procedure equipment warning you must ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 connect hose assembly to pump ... and crimper check all connections to be sure they ... are tight and leak free 2 open the pump vent plug by turning it 1-2 ... knob and tilt press as necessary insert one end of hose assembly from below the ... base plate and between the collet halves align knurl on end fitting with ... top of collet making sure that collet halves are evenly aligned 6 holding ...
equipment iiiiiiiiiiiiiiiiiiiii t-400 crimping procedure warning you must hold the ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 place die ring t-400-8 on base ... stops 2 insert properly-sized matched collet halves in the die ring see chart on ... press 3 place the correct coll-o-crimp® hose end on hose be sure hose is ... hose assembly from below between the collet halves align the dimples on the hose ... end collar with the top of the collet when crimping 265 `p series ends the ...
refer to safety information regarding coll-o-crimp® hose hose fittings and assembly ... equipment compatibility on pages 1-2 the coll-o-crimp® ii plus is ... for factory high performance machine operations construction and mine locations this ... machine offers the capabilities of crimping all of the crimp style hose ends ... weatherhead offers with this coverage this heavy-duty ... crimper can handle all of your crimping needs capacity 3/16 i.d 1 fiber braid ... through 2 6 spiral hose for hoses other than 4 and 6 spiral conversion tooling ... sold separately t-441 t-440-1 · coll-o-crimp® ii plus press only t-440-n · coll-o- ...
equipment t-420 t-440 crimping procedure procedure when using t-410 or ... t-420 series collets spacer ring may be required please ... end tool selector chart in the back of this catalog for tooling specifications ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger t-440 used in example 2 place ... proper size coll-o-crimp® hose end on hose be sure hose is bottomed in hose ... end 2a when making a hose assembly on the t-440-1 c-o-c® machine using a ...
t-420 t-440 crimping procedure t-420 used in example ... procedure when using t-400 series collets please refer to hose end tool selector ... chart in the back of this catalog for tooling specifications ... in place from below throughout the crimping operation do not place fingers or hands ... at the crimping point during operation failure to follow this procedure could ... result in serious injury to your hand or finger 1 hold switch on as ram starts ... down rotate the ram return stops out from their in position release ... allowing enough clearance for insertion of required tooling 2 open pusher halves ...
and reference in shop assembly area order hose end tool selector wall chart ... wh8889a chart warning coll-o-crimp® hose hose fittings and assembly ... equipment compatibility the coll-o-crimp equipment package coll-o-crimp end ... fittings and coll-o-crimp hose have been engineered and designed ... hose assembly system each component of the coll-o-crimp hose assembly system ... is compatible with other coll-o-crimp components to which it relates ... compatibility along with the use of high quality components ensures the ... production of reliable hose assemblies when assembled ... properly the use or intermixing of fittings and hose not specifically ...
