Motec Parts Catalog by MoTec

More catalogs by MoTec | Motec Parts Catalog | 69 pages

Ads

Contacts for MoTec

http://www.motecusa.com/

Motec Parts Catalog is listed under these categories

Automotive > Cars & Trucks > Parts and Accessories

Featured catalog pages of Motec Parts Catalog

MoTeC Parts Catalogue 2005 Page 4 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Introduction Introduction Welcome to the new MoTeC Catalogue. We are pleased to present this detailed list of our quality products with information to help you make the best choice for your application. Our range includes more items than you will probably ever need, but if you cant find what youre after, we may be able to source it for you. MoTeC products are sold through an exclusive network of authorised dealers, all qualified to advise, install and tune MoTeC systems. This service is also backed up with MoTeC factory support. For assistance from our technical support team please email your enquiry to support@motec.com.au or call MoTeC Research Centre in Australia on +61 3 9761 5050. Software for your MoTeC products is always available on our website. As upgrades or improvements are made to

MoTeC Parts Catalogue 2005 Page 11 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd M600 ECU Specifications: Featuring six injector drivers and six ignition outputs, the M600 is intended for six cylinder and triple rotary engines. Using the same sophisticated technology as the ground breaking M800, the M600 is the ideal system for late model, high tech applications. Infinitely variable cam control and Drive by Wire (DBW) control are just two of the advanced options available. Single or dual Wideband Lambda may also be enabled for fine tuning and closed loop control. Technical Drawing: M600 Standard Features: 13060 M600 Engine Control Unit Includes 8 HRS FREE WIDEBAND LAMBDA and LOGGING Factory Ref and Sync Triggers compatibility 6 Temperature inputs 8 Voltage inputs 2 Narrowband Lambda sensor inputs Hi/Low Injection control 4 Digital inputs 6 injector drivers 6 ignition drivers 8

MoTeC Parts Catalogue 2005 Page 17 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Options Include: 61021 CAN Interface Cable High speed CAN interface cable for communications from the ECU to a laptop or personal computer. 28101 LOGGING (1 MB) Allows 1mb logging of the ECU sensors and operating parameters to the internal data logging memory. The logged data may then be analysed by the MoTeC INTERPRETER Software. Data Logging option is enabled for an evaluation period of 8 hrs (engine running time) from new. 28102 SINGLE WIDEBAND LAMBDA Allows Wideband Lambda (Air Fuel Ratio) measurement, which may be used for data logging or closed loop control of the Air Fuel Ratio. The measurement is fully temperature compensated and will accurately measure ratios of 0.75 to 1.2 Lambda (11:1 to 18:1) when used with the MoTeC Wideband exhaust gas sensor. Uses latest Bosch or NTK dual cell

MoTeC Parts Catalogue 2005 Page 24 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Dash Loggers and Displays ADL2 (Advanced Dash Logger) Specifications: The ADL2 is the second evolution of MoTeCs original Advanced Dash Logger (ADL). This fully featured and selfcontained digital display and programmable data logger offers MoTeCs trademark versatility, making it suitable for a broad range of applications, including 4 wheel, 2 wheel, marine and industrial. While separate products are often used to perform logging, controlling and display functions, the MoTeC ADL2 offers seamless integration of all three. All aspects of this sophisticated Dash Logger are fully configurable, including the allocation of sensors to inputs, which channels to log and display, logging speeds, warning alarms and control outputs such as pumps, valves and solenoids. The ADL2 uses a high speed 32 bit

MoTeC Parts Catalogue 2005 Page 30 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Ignition Products CDI versus inductive ignition systems, which should you use? In an inductive ignition system, the coil is charged at battery voltage for a period of time (the dwell time) prior to firing. The dwell or charge time is controlled by the ECU, and this has to be set to match the coil being used so that the coil is not over or under charged. Undercharging reduces available spark energy, while overcharging can cause overheating of the coil and/or ignition module. Inductive ignition systems produce a long spark, at a voltage lower than that of a CDI system. A Capacitor Discharge Ignition (CDI) system is constantly charging itself and sends a large voltage charge to the coil 380- 450v. CDI systems are most often used on boosted or nitrous injected engines. These engines create tremendous

MoTeC Parts Catalogue 2005 Page 37 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Lap Timing Sensors BTX, BRX BR2 Lap Beacon System The MoTeC Lap Beacon consists of a Beacon Transmitter (BTX) and a Beacon Receiver (BR2). The Beacon Transmitter is mounted beside the track and the Beacon Receiver is mounted on the vehicle and connected to a display, data logging or an Engine Management System. The Lap Beacon system is used to mark the start and end of laps. This information can then be used by a display to show the driver lap times and lap numbers, while a MoTeC SDL or ADL2 Dash Logger can add extra functionality such as lap time gain/loss, running lap time and more. The lap beacon may also be used to generate split times by placing multiple transmitters around the race circuit. The BR2 can run in either CAN or Switched modes. The BR2 CAN networking mode sends information about all

MoTeC Parts Catalogue 2005 Page 43 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Fuel Injectors The fuel injectors available from MoTeC are a wide range of the highest quality available. We have injectors to suit almost any application, from 34hp, right up to the Indy with 300hp per injector. The following horsepower ratings are determined at 40PSI fuel pressure, and 85% duty cycle. To choose a suitable injector, realistically decide your expected power output, and divide this by the number of Injectors that you intend having. So for a 400hp V8 with 8 injectors, you would like an injector able to produce around 65hp per injector. Row 1: 007, 34035, 34036, 351, 403, Row 2: 706, 775, 803, 842, 998, Row 3: 945, 988, 989 34007 Bosch 007 Djet 50hp, 260cc/min 34035 Bosch 036 Djet 63hp, 320cc/min 34036 Bosch 036 Djet 75hp, 380cc/min 34215 Bosch 215 Ljet 34hp 34351

MoTeC Parts Catalogue 2005 Page 50 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Crank, Cam and Speed Sensors These sensors are used for measuring rotational position and speeds, they are most commonly used to measure crankshafts, camshafts, and wheel speeds. The sensors come in two main varieties, Magnetic and hall, they can be distinguished from one another by the number of wires connecting to them, with 2 pin sensors being magnetic, and 3 pin sensors being hall. Hall Sensors. Hall Sensors contain a semiconductor Hall effect IC and a magnet. The IC detects changes in the field strength as the vane passes through the sensor gap or a tooth passes the sensor tip. The output voltage changes from low to high when the leading edge of the tooth passes the centre of the sensor. The vane or tooth material must be magnetically soft (such as mild steel), do not use stainless steel.

MoTeC Parts Catalogue 2005 Page 56 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Adapters and Looms MoTeC supplies many looms to help adapt our parts to your application. These are high quality looms using only the best pins, connectors and heatshrink. Looms listed as wire in are pinned wires that you need to push into the ADL or ECU plug. Plug-in looms already have plugs on them that connect directly to an existing socket, eg. M800 OEM on board sockets. Other looms are generally sold complete with appropriate connectors already attached. Row 1: Thermocouple ext., AFM Bosch 4 wire loom, M800 OEM Lambda, M800 OEM comms can, Row 2: M800 OEM comms D9, M800 OEM Lambda, PLM Aux, M400/600/800 wire in D9 comms 62010 VDO pressure sensor adapter loom (drawing #X07) 61034 K-Type thermocouple extension wire, 1 meter 62001 AFM Lambda meter loom, Bosch 4 wire 62002 AFM Lambda

MoTeC Parts Catalogue 2005 Page 63 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Glue Heatshrink Glue heatshrink is available in the standard sizes from ES1 through to ES4. Its uses include joining standard heat shrink together at joins, acting as a strain relief at splices and joins and also as strain relieve and sealing where wiring joins on to connectors. Wire can be crimped as above can be sealed and strain relieved with glue heatshrink like this. 61202 Clear heatshrink, Ideal for wiring labels. 61203 ES1 Glue heatshrink 61204 ES2 Glue heatshrink 61205 ES3 Glue heatshrink 61206 ES4 Glue heatshrink The ES range of glue heatshrink (ES4, ES3, ES2, ES1 and

MoTeC Parts Catalogue 2005 Page 69 of 69 Copyright MoTeC Pty Ltd 22/06/2006 Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd Mounts 68076 DT connector mount (F) 68075 DT connector mount (M) 63012 ECU mount, soft (COLOURS) 62011 PLASTIC VDO pressure sensor mount Manuals and Documentation We can supply extra copies of our MoTeC manuals and documentation which are a useful tool when starting out with our products. Also available are MoTeC technical notes and Diagrams. 63018 USER MANUAL ADVANCED DASH LOGGER 2 63020 USER MANUAL INTERPRETER 63019 USER MANUAL LAP BEACON SYSTEM 63017 USER MANUAL M4 M48 ECU 63022 USER MANUAL M400/600/800/880 ECU 63023 USER MANUAL MINI DIGITAL DISPLAY 63021 USER MANUAL PROFESSIONAL LAMBDA