Catalog: High Frequency Coaxial Connectors
Company/Brand: Murata Manufacturing Co.,Ltd.
pcb connector in High Frequency Coaxial Connectors by Murata Manufacturing Co.,Ltd.
match 50 ohm impedance circuit typical pcb material is glass epoxy r=4.8 ... except for the land pattern on the pcb 2.1 3.1 1 4.1 3 1 1 1.5 1.74 1.5 4 2 1 ... of solder being trapped under connector 0.5 3.5 2.3 2 3.5 the standard solder ...
of solder being trapped under connector 2 soldering by soldering iron soldering ... flux should be thoroughly cleaned from connector to prevent possible deterioration of ... that stress by wrap and/or bend of the pcb may not apply to it 7 please avoid the ...
pulling cable when probe is locked into connector avoid twisting probe or cable when ... engaging or disengaging from connector mechanical stress the stress to the ... connector should be limited as figure shown right ... printed circuit board after connector and/or assembly has been secured to pcb ... after engagement cabed mm8430-2610b pcb 19.78maximum point for using 18. ...
match 50 ohm impedance circuit typical pcb material is glass epoxy r=4.8 ... except for the land pattern on the pcb 1.58 2 0.6 1.5 1.74 1.5 0.7 1.25 1.81 ... of solder being trapped under connector 2.5 1.5 ground 0.38 0.82 2.4 0.9 0.36 ...
of solder being trapped under connector 2 soldering by soldering iron soldering ... flux should be thoroughly cleaned from connector to prevent possible deterioration of ... that stress by wrap and/or bend of the pcb may not apply to it 7 please dry out ...
printed circuit board after connector and/or assembly has been secured to pcb ... 2 do not try to pull the cable when a connector with a coaxial cable is handled 3 ... cable when engaging or disengaging from connector 4 mechanical stress the stress to the ... connector should be limited as shown in figure 1 ...
match 50 ohm impedance circuit typical pcb material is glass epoxy r=4.8 ... 0.6 3-ø0.6 through holes pattern on the pcb 2.37 land electrode 0.6 1.5 1.74 1.5 3 ... of solder being trapped under connector 3.3 2.3 0.6 0.45 1.05 1.05 0.6 the ...
of solder being trapped under connector 2 soldering by soldering iron soldering ... flux should be thoroughly cleaned from connector to prevent possible deterioration of ... that stress by wrap and/or bend of the pcb may not apply to it 7 please dry out ...
printed circuit board after connector and/or assembly has been secured to pcb ... 2 do not try to pull the cable when a connector with a coaxial cable is handled 3 ... cable when engaging or disengaging from connector 4 mechanical stress the stress to the ... connector should be limited as shown in figure 1 ...
50 ohm impedance circuit · typical pcb material is glass epoxy r=4.8 ... except for the land pattern on the pcb in mm 1.5 1.74 1.5 0.5 0.3 2.4 note · ... 50 ohm impedance circuit · typical pcb material is glass epoxy r=4.8 ... except for the land pattern on the pcb s cable length tolerance l s profile ...
flux should be thoroughly cleaned from connector to prevent possible deterioration of ... that stress by wrap and/or bend of the pcb may not apply to it 7 please dry out ...
printed circuit board after connector and/or assembly has been secured to pcb ... 2 do not try to pull the cable when a connector with a coaxial cable is handled 3 ... 4 mechanical stress the stress to the connector should be limited as shown in figure 1 ...
flux should be thoroughly cleaned from connector to prevent possible deterioration of ... that stress by wrap and/or bend of the pcb may not apply to it 6 please dry out ...
transpoting printed circuit board after connector and/or assembly has been secured to pcb ... pull off vertically in the direction of connector coupling axis do not try to pull out by ... cable when engaging or disengaging from connector 4 mechanical stress the stress to the ... connector should be limited as shown in figure 1 ... after engagement bfa right angle plug connector abdc mm3325-2505 34 ...
