14 results for pcb mount connector pcb found in 0.000 seconds

of storage operating rating soldering mounting and handling in this catalog to prevent ... match 50 ohm impedance circuit typical pcb material is glass epoxy r=4.8 ... except for the land pattern on the pcb 2.1 3.1 1 4.1 3 1 1 1.5 1.74 1.5 4 2 1 ... of solder being trapped under connector 0.5 3.5 2.3 2 3.5 the standard solder ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... 05.8.8 1 notice s notice soldering and mounting 1 reflow soldering soldering must be ... of solder being trapped under connector 2 soldering by soldering iron soldering ... flux should be thoroughly cleaned from connector to prevent possible deterioration of ... electrical characteristics 6 please mount this product at the position so that ... stress by wrap and/or bend of the pcb may not apply to it 7 please avoid the ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... pulling cable when probe is locked into connector avoid twisting probe or cable when ... engaging or disengaging from connector mechanical stress the stress to the ... connector should be limited as figure shown right ... printed circuit board after connector and/or assembly has been secured to pcb ... after engagement cabed mm8430-2610b pcb 19.78maximum point for using 18. ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... match 50 ohm impedance circuit typical pcb material is glass epoxy r=4.8 ... except for the land pattern on the pcb 1.58 2 0.6 1.5 1.74 1.5 0.7 1.25 1.81 ... of solder being trapped under connector 2.5 1.5 ground 0.38 0.82 2.4 0.9 0.36 ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... 05.8.8 notice s notice soldering and mounting 1 reflow soldering soldering must be ... of solder being trapped under connector 2 soldering by soldering iron soldering ... flux should be thoroughly cleaned from connector to prevent possible deterioration of ... electrical characteristics 6 please mount this product at the position so that ... stress by wrap and/or bend of the pcb may not apply to it 7 please dry out ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... printed circuit board after connector and/or assembly has been secured to pcb ... 2 do not try to pull the cable when a connector with a coaxial cable is handled 3 ... cable when engaging or disengaging from connector 4 mechanical stress the stress to the ... connector should be limited as shown in figure 1 ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... match 50 ohm impedance circuit typical pcb material is glass epoxy r=4.8 ... 0.6 3-ø0.6 through holes pattern on the pcb 2.37 land electrode 0.6 1.5 1.74 1.5 3 ... of solder being trapped under connector 3.3 2.3 0.6 0.45 1.05 1.05 0.6 the ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... 05.8.8 notice s notice soldering and mounting 1 reflow soldering soldering must be ... of solder being trapped under connector 2 soldering by soldering iron soldering ... flux should be thoroughly cleaned from connector to prevent possible deterioration of ... electrical characteristics 6 please mount this product at the position so that ... stress by wrap and/or bend of the pcb may not apply to it 7 please dry out ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... printed circuit board after connector and/or assembly has been secured to pcb ... 2 do not try to pull the cable when a connector with a coaxial cable is handled 3 ... cable when engaging or disengaging from connector 4 mechanical stress the stress to the ... connector should be limited as shown in figure 1 ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... 50 ohm impedance circuit · typical pcb material is glass epoxy r=4.8 ... except for the land pattern on the pcb in mm 1.5 1.74 1.5 0.5 0.3 2.4 note · ... 50 ohm impedance circuit · typical pcb material is glass epoxy r=4.8 ... except for the land pattern on the pcb s cable length tolerance l s profile ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... 05.8.8 notice s notice soldering and mounting 1 reflow soldering soldering must be ... flux should be thoroughly cleaned from connector to prevent possible deterioration of ... electrical characteristics 6 please mount this product at the position so that ... stress by wrap and/or bend of the pcb may not apply to it 7 please dry out ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... printed circuit board after connector and/or assembly has been secured to pcb ... 2 do not try to pull the cable when a connector with a coaxial cable is handled 3 ... 4 mechanical stress the stress to the connector should be limited as shown in figure 1 ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... 15 to 85 rh 5 s notice soldering and mounting 1 soldering by soldering iron soldering ... flux should be thoroughly cleaned from connector to prevent possible deterioration of ... electrical characteristics 5 please mount this product at the position so that ... stress by wrap and/or bend of the pcb may not apply to it 6 please dry out ...

of storage operating rating soldering mounting and handling in this catalog to prevent ... transpoting printed circuit board after connector and/or assembly has been secured to pcb ... pull off vertically in the direction of connector coupling axis do not try to pull out by ... cable when engaging or disengaging from connector 4 mechanical stress the stress to the ... connector should be limited as shown in figure 1 ... after engagement bfa right angle plug connector abdc mm3325-2505 34 ...