8 search results for greater than and less than in 0.142 seconds found

ActionJac™ Worm Gear Jack systems 2016

WORM GEAR SCREW JACK ActionJac™ Worm Gear Jack systems are ruggedly designed and produced in Standard models with load handling capacities from ¼ ton to 100 tons.

ActionJac™ Worm Gear Jack systems 2016

torque is shown as torque to lift one kn of load starting torque is 50 greater than torque shown for loads less than 25 of rated loads add tare drag ... 10 end-of-travel stops are not provided 11Δstarting torque is100 greater than torque shown kw per jack torque to raise one x knn •m number ... that the recommended horsepower and temperature are not exceeded 2 ... is 50 torque shown for loads less than 25 of rated loads add tare drag

ActionJac™ Worm Gear Jack systems 2016

is shown as torque to lift one kn of load starting torque is 100 greater than torque shown forloads less than 25 of rated loads add tare drag ... 10 end-of-travel stops are not provided 11 starting torque is100 greater than torque shown 4 overload capacity of the trapezoidal screw jack is as ... the recommended horsepower and temperature are not exceeded 7 ... as boots limit switches top plates and clevises are available 2 input

ActionJac™ Worm Gear Jack systems 2016

is shown as torque to lift one pound of load starting torque is 100 greater than torque shown for machine screw jacks and 50 greater than torque shown ... is shown as torque to lift one kn of load starting torque is 100 greater than torque shown for machine screw jacks and 50 greater than the torque ... kn to be raised tare drag torque x rpm 9,549 11 starting torque is100 greater than torque shown 12 no load torque need only be added if operating under

ActionJac™ Worm Gear Jack systems 2016

is shown as torque to lift one pound of load starting torque is 50 greater than torque shown for loads less than 25 of rated loads add tare drag ... ,025 10 end-of-travel stops are not provided 12 starting torque is 50 greater than torque shown 13 measurements listed are for non-keyed jacks see ... that the recommended horsepower and temperature are not exceeded 2 ... is 50 torque shown for loads less than 25 of rated loads add tare drag

ActionJac™ Worm Gear Jack systems 2016

in-lb tare drag torque in-lb — these jacks can be supplied with handwheels and counters see actionjac™ accessories section to provide ... is shown as torque to lift one pound of load starting torque is 100 greater than torque shown for loads less than 25 of rated loads add tare drag ... be added if operating under 25 rated load 12 starting torque is 100 greater than torque shown 13 measurements listed are for non-keyed jacks see

ActionJac™ Worm Gear Jack systems 2016

is shown as torque to lift one pound of load starting torque is 100 greater than torque shown tare drag torque should be added for all loads 9 units ... x of pounds x rpm pound to be raised 63,025 13 starting torque is 100 greater than torque shown stainless steel jacks model root dia in turns of worm ... stainless steel machine screw jacks quick ... reference stainless steel jacks 2ss-msj 5ss-msj 10ss-

ActionJac™ Worm Gear Jack systems 2016

the table the trunnion pins should be made from steel with a hardness greater than 30 hrc and a yield strength greater than 60,000 psi machine screw ... jack accessories trunnion adapters bsj and msj trunnion bottom view nook actionjac™ ... a trunnion adapter plates bolt to the jack flange and have precision bores for trunnion pins g j ... trunnion pin support mounting surfaces should be less than or equal to the “a” dimension

ActionJac™ Worm Gear Jack systems 2016

worm gear screw jacks application examples u arrangement speed and horsepower the extension travel rate of 1” in 2 seconds is 30 ... the 6:1 gear ratio when using a 1750 rpm ac motor during retraction and 720 rpm during extension using the horsepower formulas on page 15 the ... weight is 16,800 lbs • when fully extended the total load is less than 5,000 lbs • the load will be in compression • total