Catalog: Constant Velocity Joints for Industrial Machines
Company/Brand: NTN Corporation Japan
splined shaft installation in Constant Velocity Joints for Industrial Machines by NTN Corporation Japan
no need for intermediate slide spline shaft cup type bj75cbj225c 25° greater ... flange type doj225fdoj625f short shaft series long shaft series 20° 8° to 10° ... bc200 2 5° no alignment is needed easy installation 1 the maximum allowable operating angle ... here the bell type cvjs used for drive shafts of automobiles passenger cars trucks ...
side packing outer race inner race boot shaft flanged hub cage balls boot retainer ... 1 the free side cvj can come off the splined shaft be very careful when handling it ... splines are needed for the intermediate shaft the intermediate shaft does not need ... splines since the axial expansion and installation mounting distance adjustment are ... sliding splines of the inner race and shaft at the free side shorter shaft length ... the intermediate shaft can be designed to be much shorter ... of high-speed rotation the solid shafts for high-speed joints have been ... precisionmachined and the steel pipe shafts have been dynamically balance higher ...
boot band boot band cage ball booth shaft features remarks greater allowable ... angle caution 1 the intermediate splined shaft of clt and clft series can come ... the cvjs with intermediate slide spline shaft offer greater axial expansion easy ... installation and removal the cvj proper is secured ...
c-ring ball round-section circlip boot shaft features expansion is possible within ... correlation operating method and installation/removal method should be considered for ... as compared with generic slide spline shaft see fig 1 8 axial vibration can be ... splines are needed for the intermediate shaft the intermediate shaft does not need ... splines since the axial expansion and installation mounting distance adjustment are ... by the structure inside the cvjs easy installation both axial expansion and operating ... a larger length variation allowing easy installation 0° 5° 10 15° 20° operating angle of cvj ... terms of torque capacity expansion and installation system fig 1 sliding friction 8 ...
outline coupling type short shaft series outer race cage square-section ... inner race round-section circlip shaft o-ring flanged hub ball c-ring boot ... spring hexagon washer headed bolt long shaft series outer race inner race square- ... c-ring ball round-section circlip boot shaft features no alignment work is necessary ... the offset across both shafts when the coupling is installed is 3.5 ... to 11.5 mm in the case of short shaft series joints see fig 1 the long shaft ... the maximum crossed angle between two shafts is 5° furthermore this type of joint ... small also when a long intermediate shaft is needed the middle portion of the ... shaft is composed of steel pipe this light- ... generic slide spline arrangement easy installation both flanged hubs are installed to the ... mating shafts then the couplings are fastened to ...
authorized grease to the splines on the shaft photo 6 photo 5 step 7 procedure for ... cause it to fly off if it slips during installation photo 6 e-ring photo 7 e-ring photo 8 ...
mount the joint assembly on the shaft until the end face of the inner race ... the groove for retainer plate on the shaft photo 9 photo 9 2 install the splined ... splines mesh with the splines on the shaft photo 10 splined retainer plate photo ... also align the teeth of splines on the shaft with tooth spaces on the retainer plate ... with the hexagon headed bolts photo 11 shaft retainer plate photo 11 step 8 inject ... the fixed side cvj except for step 3 installation of the square-section circlip and step ... 7 installation of the e-ring or locking of the ...
diameter and small diameter over the shaft photo 13 photo 13 step 2 fit the boot ... over the shaft fit the square-section circlip into the ... groove on the shaft 1 photo 14 1 for installation procedure with the square-section ... velocity joints to the splines on the shaft photo 16 55 ...
diameter and small diameter over the shaft and shift them to the steel pipe side ... then fit the boot over the shaft photo 21 photo 21 step 2 fit the square ... -section circlip into the groove on the shaft 1 photo 22 1 for installation procedure ... velocity joints to the splines on the shaft photo 24 57 ...
