Selected page of Tube Fabricating Equipment
Tube Fabricating Equipment
Parker Hannifin Corporation
Instrumentation Connectors Division
Huntsville, Alabama
4
Medium Duty Bender, 2829S
Medium Duty Inch and Metric Hand Tube
Benders
Base Part No. 2829
Designed and built for fast, accurate bends and long
service life.
These are individual benders for eight inch tube sizes (1/8",
3/16", 1/4", 5/16", 3/8", 1/2", 5/8", 3/4") and six metric sizes (5mm,
6mm, 8mm, 10mm, 12mm, and 14mm). Will bend copper, aluminum,
annealed steel and stainless steel. Can be used in hands or mounted
in a bench vise. Simply align marks on slide block and radius block
then bend to desired angle (up to 180°) by pulling steadily on slide
block handle. Angles are indicated on radius block, both front and
back. (Detailed instructions are included with each bender.)
See Table N2, on page 15, for inch part numbers and technical data.
See Table N3, on page 15, for metric part numbers and technical
data.
1" Hand Tube Bender
Part No. 16-2829
| Tube Fabricating Equipment
Parker Hannifin Corporation
Instrumentation Connectors Division
Huntsville, Alabama
6
ICD Ferrule Hydraulic Presetting Tool Kit
Ferrule Presetting Tool Kit
Fitting
Size
Tube
O.D.
Part No.
Fitting
Size
Tube
O.D.
Part No.
Instrumentation Hand Pre-Setting Tools
Ferrule pre-setter (sizes 2 to 16)
2
1/8
2-Hand Preset Tool
10
5/8 10-Hand Preset Tool
4
1/4
4-Hand Preset Tool
12
3/4 12-Hand Preset Tool
5
5/16
5-Hand Preset Tool
14
7/8 14-Hand Preset Tool
6
3/8
6-Hand Preset Tool
16
1 16-Hand Preset Tool
8
1/2
8-Hand Preset Tool
Parker Instrumentation
Ferrule pre-setter
(sizes 2 to 16)
How To Use: Slide nut and ferrule(s) onto tube. Set tube into presetting tool, and
bottom tube against shoulder tool. Finger tighten the nut and then tighten the nut 1
turn with a wrench. Remove tube from tool. Advance the nut so it is finger-tight.
Advance the nut 1/2 turn. If torque rise is not felt
| Tube Fabricating Equipment
Parker Hannifin Corporation
Instrumentation Connectors Division
Huntsville, Alabama
8
L
TUBE O.D.
Pre-setting the CPI /A-LOK Tube Fitting Ferrules
Size 1-1/4" and 2"
1. Assemble CPI nut, CPI Ferrule and body die onto tubing as
shown in figure 1. Be sure that the tapered end of the Ferrule
points toward the body die.
2. Insert U-shaped Nut Support ring into the back-up plate of the
Hydraulic Ram as shown in Figure 2.
3. Insert Tube Assembly, (Figure 1) into Nut Support as shown in
Figure 3.
4. Close the pressure relief valve on the side of the hand pump.
Pump the hand pump until the ram reaches a positive stop. At
this point an increase in resistance of the handle will be felt and
the nut will bottom against the shoulder of the body die (Figure 4).
5. Release the hydraulic pressure by opening the relief valve on the
side of the pump. The ram will automatically return to the
original position.
6. The ferrule(s) is now pre-set on the t
| Tube Fabricating Equipment
Parker Hannifin Corporation
Instrumentation Connectors Division
Huntsville, Alabama
10
Gaugeablity Tools
Tube Marker
Put burnish marks on the tubing quickly and accurately with this
easy-to-use tube marker. Also used to check the burnish mark
position. (Good for the life of the fitting.)
Inspection Gauges
This handy gauge does double duty. Use the No-Go portion (on one
end) to check the tube insertion depth. Use the other end to check
the space between the nut and body hex. (Proper initial make-up
prevents the gauge from being inserted.)
Tube Marker
Ensures proper tube depth insertion into the fitting
body.
This compact C-Ring gauge is for inch and metric
sizes. Effectively checks the gap dimensions for
proper initial make-up. Can be combined on a key
ring for easy handling.
Size
Tubing O.D.
2
1/8
4
1/4
6
3/8
8
1/2
10
5/8
12
3/4
14
7/8
16
1
Instrumentation Tube Fitting Video
Training Program
A co
| Tube Fabricating Equipment
Parker Hannifin Corporation
Instrumentation Connectors Division
Huntsville, Alabama
12
Gas Service
Special care must be taken when selecting tubing for gas service. In order to achieve a gas-tight seal, ferrules in instrument
fittings must seal any surface imperfections. This is accomplished by the ferrules penetrating the surface of the tubing.
Penetration can only be achieved if the tubing provides radial resistance and if the tubing material is softer than the ferrules.
Thick walled tubing helps to provide resistance. Tables 2-7 indicate the minimum acceptable wall thickness for various
materials in gas service. The ratings in white indicate combination of diameter and wall thickness which are suitable for gas
service.
Acceptable tubing hardness for general application is listed in Table 9. These values are the maximum allowed by ASTM. For
gas service, better results can be obtained by using tubing well below this maximum hardness. For example
| Tube Fabricating Equipment
Parker Hannifin Corporation
Instrumentation Connectors Division
Huntsville, Alabama
14
.010
.020
.028
.035
.049 .065
.083
.095
.109
.120
1/16
5900
12600
17000
1/8
8600
11000
3/16
5500
7100
10300
1/4
4000
5100
7500
10300
5/16
4000
5900
8100
3/8
3300
4800
6600
1/2
2300
3300
4500
5900
5/8
2800
3700
4900
5700
3/4
2300
3100
4000
4600
5400
1
2300
2900
3400
3900
4400
WALL THICKNESS
Tube
O.D.
Size
Table 7
MONEL 400 (Seamless)
Note: All working pressures have been
calculated using the maximum allowable
stress levels in accordance with ANSI
B31.3, Chemical Plant and Petroleum
Refinery Piping Code, 1987 Edition
All Calculations are based on maximum
outside diameter and minimum wall
thickness
All working pressures are at ambient
(72°F or 22°C) temperature.
100
(38)
1.00
1.00
1.00
1.00
1.00
1.00
200
(93)
0.80
1.00
1.00
1.00
.96
.88
| Tube Fabricating Equipment
Parker Hannifin Corporation
Instrumentation Connectors Division
Huntsville, Alabama
16
Hand Crank Hydraulic Bender Capacity Guide Metric Sizes
Table N5 Hand Crank and Hydraulic Tube Benders
Maximum Capacity Guide Metric Sizes
Tube
Tube Wall Thickness (mm)
O.D.
1.5
2
2.5
3
3.5
4
5
(mm)
Material
Bender Code*
18
S
ABCD
ABCD
ABCD
ABCD
BCD
BCD
D
SS
BCD
BCD
BCD
BCD
BCD
BCD
D
20
S
ABCD
ABCD
ABCD
BCD
BCD
BCD
D
SS
BCD
BCD
BCD
BCD
BCD
BCD
D
22
S
BCD
BCD
BCD
BCD
BCD
BCD
D
SS
BCD
BCD
BCD
BCD
BCD
D
D
25
S
BCD
BCD
BCD
BCD
BCD
D
D
SS
BCD
BCD
BCD
BCD
D
D
D
28
S
BCD
BCD
BCD
BCD
D
D
D
SS
BCD
BCD
D
D
D
D
D
30
S
BCD
BCD
BCD
BCD
D
D
D
SS
BCD
BCD
D
D
D
D
D
32
S
BCD
BCD
D
D
D
D
D
SS
BCD
D
D
D
D
D
D
38
S
CD
D
D
D
D
D
| Tube Fabricating Equipment
Parker Hannifin Corporation
Tube Fittings Division
Columbus, Ohio
18
FOR MORE INFORMATION ON THESE PRODUCTS, PLEASE CALL
THE TUBE FITTINGS DIVISION AT (614) 279-7070.
THREAD
IDENTIFICATION KIT
THREAD IDENTIFICATION KIT
............................................................. PG. 19
PARKER HANNIFIN CORPORATION ALSO MANUFACTURES A WIDE RANGE OF
TUBE FITTINGS AND TUBE FABRICATION EQUIPMENT INCLUDING:
SEALANTS, LUBRICANTS CLEANERS
....................................... PG. 19
TEFLON
TAPE
PERMATEX
ANTI-SEIZE
LUBRICANT
LOCTITE
7649
PRIMER N
LOCTITE
THREAD
SEALANT 565
LOCTITE
THREAD
SEALANT 545
LOCTITE
THREADLOCKER
271
LOCTITE
THREADLOCKER 242
PERMATEX HAND
CLEANER
FAST ORANGE
WIPES
TUBE FITTING AND TUBE FABRICATION EQUIPMENT AVAILABLE FROM
PARKER HANNIFINS TUBE FITTINGS DIVISION
O-RING INSTALLATION KIT
O-RING ASSEMBLY
CAPTIVE O-RING TOOL
CUTTING DEBURRING TOOLS
CUT-OFF
SAW
POWER DEBURR
TOOL
BENDERS
EXACTO
| Tube Fabricating Equipment
Parker Hannifin Corporation
Tube Fittings Division
Columbus, Ohio
20
Loctite Thread Sealant 565
Loctite Thread Sealant 565
Formulated specifically for metal tapered pipe thread fittings. PST
565 cures rapidly to provide immediate low pressure sealing. Its controlled lubricity prevents galling and it protects mated thread areas
from rust and corrosion.
Application: Stainless steel tapered pipe threads
Sizes available
Part No.
6 ml tube ................................................................................... 25117
36 ml tube ................................................................................. 56521
Loctite Thread Sealant 545
Designed for both hydraulic and pneumatic systems, 545 contains no
fillers or particles which could contaminate system fluids, foul valves,
or clog fine filters and screens.
Applications: Steel and brass tapered pipe threads
Sizes available
Part No.
.5 ml capsule ................................
| Offer of Sale
Parker Hannifin Corporation
Instrumentation Connectors Division
Huntsville, Alabama
22
1. Terms and Conditions of Sale: All descriptions, quotations, proposals,
offers, acknowledgments, acceptances and sales of Sellers products are
subject to and shall be governed exclusively by the terms and conditions
stated herein. Buyers acceptance of any offer to sell is limited to these terms
and conditions. Any terms or conditions in addition to, or inconsistent with
those stated herein, proposed by Buyer in any acceptance of an offer by
Seller, are hereby objected to. No such additional, different or inconsistent
terms and conditions shall become part of the contract between Buyer and
Seller unless expressly accepted in writing by Seller. Sellers acceptance
of any offer to purchase by Buyer is expressly conditional upon Buyers
assent to all the terms and conditions stated herein, including any terms in
addition to, or inconsistent with those contained in Buyers off
| Parker Hannifin Corporation
Instrumentation Connectors Division
P.O. Box 400004-1504
Huntsville, AL 35815-1504
USA
Phone: (256) 881-2040
Fax: (256) 881-5730
www.parker.com/ICD
Catalog 4290, 20M, 07/00
|
|
