Catalog: Tube Fabricating Equipment | |
| , Alabama 6 ICD Ferrule Hydraulic Presetting Tool Kit Ferrule Presetting Tool Kit ... Size Tube O.D. Part No. Instrumentation Hand Pre-Setting Tools Ferrule pre-setter ( ... sizes 2 to 16) 2 1/8 2-Hand Preset Tool 10 5/8 10-Hand Preset Tool 4 1 ... /4 4-Hand Preset Tool 12 3/4 12-Hand Preset Tool 5 5/16 5-Hand Preset Tool 14 7 ... /8 14-Hand Preset Tool 6 3/8 6-Hand Preset Tool 16 1 16-Hand Preset Tool 8 1/2 ... 8-Hand Preset Tool Parker Instrumentation Ferrule pre ... and ferrule(s) onto tube. Set tube into presetting tool, and bottom tube against shoulder ... , and makeup nut 1/2 turn. Assembly Tools Par-Lok Wrench Kit The Par-Lok Wrench ... tubing. The wrenches are packaged in a handy vinyl pouch. Par-Lok Wrench Kit An ICD ... | |
| , Alabama 7 Figure 3 Figure 4 Ferrule Presetting Components 1/4" 4 4 Body Die Size 4 Nut ... " 8 8 Body Die Size 8 Nut Die Hydraulic Hand Pump Enerpac Pump P-392 5/8" 10 10 ... Die Size 16 Body Die Adapter Note: To preset 1 ferrules with B Tool a size 16 Body ... Hy-Fer-Set Kit Components Part No. Presetting CPI A-LOK Tube Fitting Ferrules Sizes 1 ... as shown in Figure 3. 4. Close the pressure relief valve on the side of the hand ... pump. Pump the hand pump until the ram reaches a positive ... point an increase in resistance of the handle will be felt and the nut will bottom ... (Figure 4). 5. Release the hydraulic pressure by opening the relief valve on the side ... position. 6. The ferrule(s) is now pre-set on the tubing. Remove the preset ... . If the body die does not pull off by hand, clamp on the outside of the body die ... | |
| Huntsville, Alabama 8 L TUBE O.D. Pre-setting the CPI /A-LOK Tube Fitting Ferrules ... as shown in Figure 3. 4. Close the pressure relief valve on the side of the hand ... pump. Pump the hand pump until the ram reaches a positive ... point an increase in resistance of the handle will be felt and the nut will bottom ... (Figure 4). 5. Release the hydraulic pressure by opening the relief valve on the side ... position. 6. The ferrule(s) is now pre-set on the tubing. Remove the pre-set ... . (If the body die does not pull off by hand, clamp on the outside of the body die ... pulling. Do not clamp or pull on the pre-set ferrule(s) as this could damage a ... sealing surface. 7. Insert the pre-set assembly into a fitting body, and make ... is not felt early in wrench makeup, the pre-set assembly was not properly seated.) If ... | |
| on tube fitting nut. 6. Insert properly prepared tubing into tube fitting. Make certain ... This eliminates the need for hydraulic pre-setting and hand wrench tightening. No bulky ... wrench tight prior to assembly. By hand, use the rotary wrench to draw the nut ... body hex to indicate starting point 10. Press advance button on remote control and ... of marks on nut and body. (Assembly Tools contd) For more information, see ... ahead of any bend to fit into the pre-setting tool. See the L dimension in the chart ... | |
| Huntsville, Alabama 10 Gaugeablity Tools Tube Marker Put burnish marks on the ... of the fitting.) Inspection Gauges This handy gauge does double duty. Use the No-Go ... and body hex. (Proper initial make-up prevents the gauge from being inserted.) Tube ... Can be combined on a key ring for easy handling. Size Tubing O.D. 2 1/8 4 1/4 6 3 ... training program for proper selection, preparation, assembly and installation. The Parker ... factors; types of fittings - Tube preparation - Tube system installation Parker A- ... and go/no go gauge - Proper use of hand pre-set and HyFerSet tools - Port ends ... and maintenance technicians to help prevent these incidents and their often costly ... Safety Seminar Parker provides hands on safety seminars for the proper ... selection, preparation, tube bending and instrumentation ... | |
