Catalog: Tube Fabricating Equipment | |
| , Alabama 6 ICD Ferrule Hydraulic Presetting Tool Kit Ferrule Presetting Tool Kit ... Tube O.D. Part No. Instrumentation Hand Pre-Setting Tools Ferrule pre-setter (sizes 2 to 16 ... ) 2 1/8 2-Hand Preset Tool 10 5/8 10-Hand Preset Tool 4 1 ... /4 4-Hand Preset Tool 12 3/4 12-Hand Preset Tool 5 5/16 5-Hand Preset Tool 14 7 ... /8 14-Hand Preset Tool 6 3/8 6-Hand Preset Tool 16 1 16-Hand Preset Tool 8 1/2 ... 8-Hand Preset Tool Parker Instrumentation Ferrule pre ... -setter (sizes 2 to 16) How To Use: Slide nut ... and ferrule(s) onto tube. Set tube into presetting tool, and bottom tube against shoulder ... , and makeup nut 1/2 turn. Assembly Tools Par-Lok Wrench Kit The Par-Lok Wrench ... Lok Wrench Kit An ICD Ferrule Hydraulic Presetting Tool Kit is available for making up 1/4 ... | |
| , Alabama 7 Figure 3 Figure 4 Ferrule Presetting Components 1/4" 4 4 Body Die Size 4 Nut ... 3/8" 6 6 Body Die Size 6 Nut Die Hy-Fer-Set Body Assembly 1/2" 8 8 Body Die Size 8 ... Die Size 16 Body Die Adapter Note: To preset 1 ferrules with B Tool a size 16 Body ... Die Nut Die Item Part Number Hy-Fer-Set Kit Components Part No. Presetting CPI ... as shown in Figure 3. 4. Close the pressure relief valve on the side of the hand ... (Figure 4). 5. Release the hydraulic pressure by opening the relief valve on the side ... position. 6. The ferrule(s) is now pre-set on the tubing. Remove the preset ... pulling. Do not clamp or pull on the pre-set ferrule(s) as this could damage a ... sealing surface. 7. Insert the pre-set assembly into a fitting body, and make ... is not felt early in wrench makeup, the pre-set assembly was not properly seated.) If ... | |
| Huntsville, Alabama 8 L TUBE O.D. Pre-setting the CPI /A-LOK Tube Fitting Ferrules ... as shown in Figure 3. 4. Close the pressure relief valve on the side of the hand ... (Figure 4). 5. Release the hydraulic pressure by opening the relief valve on the side ... position. 6. The ferrule(s) is now pre-set on the tubing. Remove the pre-set ... pulling. Do not clamp or pull on the pre-set ferrule(s) as this could damage a ... sealing surface. 7. Insert the pre-set assembly into a fitting body, and make ... is not felt early in wrench makeup, the pre-set assembly was not properly seated.) If ... ahead of any bend to fit into the pre-setting tool. See the L dimension in the chart ... each tube O.D. size. L Chart (Assembly Tools contd) Table 2 Threads Size Body Die ... Nut Die Item Part Number Hy-Fer-Set Kit Components 1-1/4" 20 20 Body Die ... | |
| on tube fitting nut. 6. Insert properly prepared tubing into tube fitting. Make certain ... This eliminates the need for hydraulic pre-setting and hand wrench tightening. No bulky ... body hex to indicate starting point 10. Press advance button on remote control and ... of marks on nut and body. (Assembly Tools contd) For more information, see ... Die Nut Die Item Part Number Hy-Fer-Set Kit Components 1-1/4" 20 20 Body Die ... ahead of any bend to fit into the pre-setting tool. See the L dimension in the chart ... | |
| Huntsville, Alabama 10 Gaugeablity Tools Tube Marker Put burnish marks on the ... and body hex. (Proper initial make-up prevents the gauge from being inserted.) Tube ... training program for proper selection, preparation, assembly and installation. The Parker ... factors; types of fittings - Tube preparation - Tube system installation Parker A- ... and go/no go gauge - Proper use of hand pre-set and HyFerSet tools - Port ends ... and maintenance technicians to help prevent these incidents and their often costly ... seminars for the proper selection, preparation, tube bending and instrumentation ... seminars. CD Rom, (Powerpoint or slide presentation(s) for customer tailored safety ... For more information on Gaugeability Tools, see page 17 Assembly, Remake, and ... | |
