Catalog: Tube Fabricating Equipment | |
| Tube Fabricating Equipment Parker Hannifin ... 6 ICD Ferrule Hydraulic Presetting Tool Kit Ferrule Presetting Tool Kit ... Fitting Size Tube O.D. Part No. Fitting Size Tube O.D ... No. Instrumentation Hand Pre-Setting Tools Ferrule pre-setter (sizes 2 to 16) 2 ... 1/8 2-Hand Preset Tool 10 5/8 10-Hand Preset Tool 4 1/4 4- ... Hand Preset Tool 12 3/4 12-Hand Preset Tool 5 5/16 5 ... -Hand Preset Tool 14 7/8 14-Hand Preset Tool 6 3/8 6- ... Hand Preset Tool 16 1 16-Hand Preset Tool 8 1/2 8-Hand Preset Tool Parker ... (sizes 2 to 16) How To Use: Slide nut and ferrule(s) onto tube. Set tube into ... presetting tool, and bottom tube against shoulder tool. Finger tighten ... the nut and then tighten the nut 1 turn with a wrench. Remove tube from ... | |
| Tube Fabricating Equipment Parker Hannifin ... Components 1/4" 4 4 Body Die Size 4 Nut Die Kit A Hydraulic Ram Hydraulic Ram ( ... size 4-16) 3/8" 6 6 Body Die Size 6 Nut Die Hy-Fer-Set Body Assembly 1/2" 8 8 ... Body Die Size 8 Nut Die Hydraulic Hand Pump Enerpac Pump ... P-392 5/8" 10 10 Body Die Size 10 Nut Die Hose Assembly Hose Assembly w/ ... guards 3/4" 12 12 Body Die Size 12 Nut Die Carrying Case Carrying Case 7/8" 14 ... 14 Body Die Size 14 Nut Die 1" 16 16 Body Die Size 16 Nut Die ... Note: To preset 1 ferrules with B Tool a size 16 Body Die Adapter must be used ... . Threads Size Body Die Nut Die Item Part Number Hy-Fer-Set Kit ... Part No. Presetting CPI A-LOK Tube Fitting Ferrules Sizes 1/4" Through 1" ... 1. Assemble CPI /A-LOK nut, CPI /A-LOK Ferrule(s) and body die onto ... toward the body die. 2. Insert U-shaped Nut Support ring into the back-up plate of ... | |
| Tube Fabricating Equipment Parker Hannifin ... Division Huntsville, Alabama 8 L TUBE O.D. Pre-setting the CPI /A-LOK Tube ... Size 1-1/4" and 2" 1. Assemble CPI nut, CPI Ferrule and body die onto tubing as ... toward the body die. 2. Insert U-shaped Nut Support ring into the back-up plate of ... Ram as shown in Figure 2. 3. Insert Tube Assembly, (Figure 1) into Nut Support ... of the handle will be felt and the nut will bottom against the shoulder of the ... seats in the fitting. Tighten the nut on the fitting body until finger tight ... . 8. Tighten the nut with a wrench the additional amount ... seated.) If this happens, tighten the nut with a wrench until the torque increase ... is felt. Then loosen the nut to the fingertight position, tighten ... the nut the additional amount shown in Table 2 ... | |
| Tube Fabricating Equipment Parker Hannifin ... Wrench Assembly Kit PAK-32 HYTORC L TUBE O.D. The Parker P32 Rotary Wrench Size ... proper split insert (20-24-32) to fit tube nut hex. Place split insert in rotary ... . Position rotary wrenchs hex insert on tube fitting nut. 6. Insert properly ... prepared tubing into tube fitting. Make certain to feel tubing ... in fitting body. Finger-tighten the nut and ferrule assembly. This eliminates ... hand, use the rotary wrench to draw the nut and ferrule(s) to their proper position ... pad F , and secure open end to tube body hex. 9. Mark nut and body hex to ... by relative alignment of marks on nut and body. (Assembly Tools contd) For ... -B2 or P32 Video. Threads Size Body Die Nut Die Item Part Number Hy-Fer-Set Kit ... 1-1/4" 20 20 Body Die Size 20 Nut Die Kit B Hydraulic Ram (size 20-32) 1- ... | |
| Tube Fabricating Equipment Parker Hannifin ... Huntsville, Alabama 10 Gaugeablity Tools Tube Marker Put burnish marks on the ... and accurately with this easy-to-use tube marker. Also used to check the burnish ... No-Go portion (on one end) to check the tube insertion depth. Use the other end to ... check the space between the nut and body hex. (Proper initial make-up ... the gauge from being inserted.) Tube Marker Ensures proper tube depth ... 3/4 14 7/8 16 1 Instrumentation Tube Fitting Video Training Program A ... Basics of Tubing System Fabrication - Tube selection factors; types of fittings - ... Tube preparation - Tube system installation Parker A-LOK ... and remake procedures - Proper use of tube marker and go/no go gauge - Port ends ... and remake procedures - Proper use of tube marker and go/no go gauge - Proper use ... | |
| Tube Fabricating Equipment Parker Hannifin ... Corporation Tube Fittings Division Columbus, Ohio 20 ... threads Sizes available Part No. 6 ml tube ... 25117 36 ml tube ... strength threadlocker is ideal for all nut and bolt applications. It eliminates ... the need for stocking expensive lock nuts and washers. Its other advantages ... , and easy disassembly with hand tools. Applications: All fastener applications ... . DO NOT USE THIS PRODUCT WITH PARKER TUBE FITTINGS. RECOMMENDED ONLY FOR FASTENER ... . Sizes available Part No. 6 ml tube ... 24200 36 ml tube ... require extra effort or special tools for removal. Thread sealants seal and ... are easily removed with basic hand tools. Thread sealants can be used on pipe ... | |
