Catalog: L-2008 Penco Locker Catalog | |
| imperfection and capable of taking a high grade enamel finish hinges .074 thick ... 2 high double spun full loop tight pin five- ... butt hinges projection welded to door frame and securely fastened to the door ... with 2 steel rivets doors over 48 high shall have three hinges all other doors ... each locker shall have an individual door and frame individual top bottom back ... square rigid and without warp doors shall be flat and free of distortion ... door frame all door frame members to be not less than 16 ... flange to provide a continuous door strike intermembering parts to be ... bend backs sides shall be 24 gauge doors doors 30 or higher shall be formed ... piece 16 gauge cold rolled sheet steel doors less than 12 wide shall be minimum of ... formations across the top and bottom doors over 15 wide x 60 72 high shall ... | |
| imperfection and capable of taking a high grade enamel finish hinges .074 thick ... 2 high double spun full loop tight pin five- ... knuckle hinges projection welded to door frame and securely fastened to the door ... with 2 steel rivets doors over 48 high and less than 24 wide shall have three ... hinges smaller doors shall have two hinges doors 24 wide x ... 60 or 72 high shall have one door per opening and four hinges per door ... each locker shall have an individual door and frame individual top bottom back ... square rigid and without warp doors shall be flat and free of distortion ... door frame all door frame members to be not less than 16 ... flange to provide a continuous door strike intermembering parts to be ... bend backs sides shall be 24 gauge doors doors 20 or higher shall be formed ... | |
| imperfection and capable of taking a high grade enamel finish hinges .074 thick ... 2 high double spun full loop tight pin five- ... knuckle hinges projection welded to door frame and securely fastened to the door ... with 2 steel rivets doors over 48 high shall have three hinges all other doors ... hinges except the 24 wide x 60 or 72 doors which shall have four hinges finishing ... each locker shall have an individual door and frame individual top bottom back ... square rigid and without warp doors shall be flat and free of distortion ... door frame all door frame members to be not less than 16 ... flange to provide a continuous door strike intermembering parts to be ... all other body parts shall be 16 gauge doors doors 20 or higher shall be formed ... formations across the top and bottom doors over 15 wide and over 30 high shall ... | |
| imperfection and capable of taking a high grade enamel finish finishing ... into a one piece structure side and door frame shall be manufactured from 16 ... to a channel shape with a continuous door strike two and three tier lockers shall ... 48 wide shall have two piece backs doors doors 20 or higher shall be formed ... formations across the top and bottom doors over 15 wide and over 30 high shall ... pan welded to the inside face of the door on 6 centers doors for box lockers 4 5 ... 6 8 9 tiers high shall be 14 gauge steel and have ... angle flanges on the top and bottom door handle latching 1 2 3 tier handles ... shall be recessed in the door and be finger lift control the 20 gauge ... steel securely fastened to the door with two tabs plus a positive tamper ... from protruding beyond the face of the door a lock hole cover plate shall be ... | |
| and the low maintenance inherent in a door with no moving parts it is available ... perforations louvers or as a solid door · greater tamper resistance · increased ... · improved performance with built-in locks welded lockers with mini louvers on a ... with defiant ii single point latch spl doors substitute the following specifications ... for doors door handle latching 1 2 3 tier ... on the following page delete door handle latching 4 to 9 tier box ... lockers doors all doors shall be formed from one piece 14 gauge ... limiting motion in any direction on doors measuring 12 through 18 wide ... welded a maximum of 8 on center to the door skin to maximize door rigidity doors ... welded a maximum of 8 on center to the door skin along the upper and lower pan edge ... strength quiet operation and stiffness door shall be manufactured to allow ... | |
| iron welded specifications ventilation doors doors 20 or higher shall be perforated ... shaped openings ¾ wide x 1-1/2 high other doors shall have available in 1 2 ... and 6 tier models doors are 14 gauge for 1 and 2 tier small ... perforations 7/16 wide and 15/16 high lockers there is a choice between ... single point latch doors with stainless number plates each ... locker door shall be supplied with a polished steel ... aluminum number plate 2-1/4 wide x 1 high with black numerals not less bottoms ... steel perforated sides and than 3/8 high number plates shall be attached to the ... face of the door perforated intermediate partitions are ... perforated metal for ventilation hinges doors shall be hinged on the right side with ... prime grade mild cold rolled steel tier door and two hinges on each 2 through 6 tier ... | |
| protough defiant ii single point latch doors doors 20 or higher shall have an outer ... 18 gauge inner panel welded to the door provides a double pan which stiffens ... and strengthens the door improving its resistance to prying ... doors less than 20 high for 6 tier box lockers shall be 14 ... side top and bottom flanges of all doors shall have a 90 degree bend door handle ... 2 tier handles shall be recessed in the door the formed pocket shall be brushed ... steel securely fastened to the door with two lugs plus a positive tamper- ... from protruding beyond the face of the door a lock hole cover plate shall be ... stainless steel for superior strength door pull shall be formed in the pocket ... pocket and pull shall be integral doors shall have a catch to retain unlocked ... | |
| challenges with a single locker-based security solution what are the smartlocker ... advantages security and management the administration ... swipes an approved id card their locker door quickly unlocks with no need to ... personal property lockers fire house high school corridor lockers gym lockers ... opened by locker administrator high school media center day use lockers ... | |
| to accept built-in key or combination locks padlocks and in certain circumstances ... coin or card locks locks are always ordered separately built-in ... key locks available in flat key or grooved key ... in many different key combinations or keyed alike if required dead bolt ... rh applications built-in combination locks available with five combination changes ... for security year to year master key controlled ... or private applications that require security with the assurance that keys will be ... not available for defiant lockers locks a b bench tops wood bench tops width ... a heavy duty bench pedestal 16-1/4 high pedestal consists of a heavy duty steel ... is 16-1/4 cat no 60827h ada compliant locks key locks for doors with classic iii ... required and lift latch pull to open door model no 9676a has an oversized keyhead ... | |
| holes pedestal shall be 16-1/4 high for an overall bench height of 17-1/2 ... shall be finished to match lockers locks specify lock brand if desired location ... and locker type if appropriate all locks shall have bolt types appropriate to ... of locker operations built-in flat key locks lockers shall be equipped with built-in ... flat key type locks all locks shall be master keyed to the same ... for the system built-in grooved key locks pin tumbler lockers shall be equipped ... with built-in grooved key type locks all locks shall be master keyed to the ... for the system built-in combination locks lockers shall be equipped with built-in ... combination locks locks shall have three-number combination ... owner padlocks-combination type master keyed combination type padlocks shall be ... | |
