Page 15 of L-2008 Penco Locker Catalog by Penco Products, Inc.

guardiantm defianttm ii spl guardian defiant ii single point latch spl specifications when specifying guardian lockers with defiant ii single point latch doors substitute the following specifications for doors and door handle latching 1 2 3 tier to the guardian specification on the previous page doors all doors shall be formed from 14 gauge steel formations shall be channel shape on the hinge and latch sides and right angle formations across the top and bottom top and bottom flanges shall have one 90 degree bend the latch side formation shall include a slot to fully engage an additional anti-pry lug integral with the padlock hasp limiting motion in any direction on doors measuring 12 through 18 wide additional reinforcement shall be in the form of a vertical 18 gauge pan measuring 3-1/2 wide mig-welded to the top and bottom flanges and hinge side channel with an additional ½ flange spot welded a maximum of 8 on center to the door skin to maximize door rigidity doors measuring more than 18 wide shall be reinforced using a 20 gauge horizontal box pan mig-welded a maximum of 8 on center to the hinge and latch side channels and spot welded to the door skin a maximum of 8 on center along the upper and lower pan edge for optimum strength quiet operation and stiffness door shall be manufactured to allow ventilation and stiffness hinge 16 gauge continuous hinges full length of the door are welded to the door and riveted to the frame door handle latching 1 2 3 tier handles shall be recessed in the door the formed pocket shall be brushed stainless steel securely fastened to the door with two lugs plus a positive tamper resistant fastener the pocket shall be of sufficient depth to prevent a combination padlock built-in combination lock or key lock from protruding beyond the face of the door an anti-pry lock alignment bracket shall be supplied for use with built-in combination locks to facilitate installation adjustment and to increase resistance to prying by mechanically engaging the hasp assembly a lock hole cover plate shall be provided for use with padlocks all pockets shall be 22 gauge drawn stainless steel for superior strength door pull shall be formed in the pocket pocket and pull shall be integral the single point alternative the defiant ii single point latch spl option for guardian lockers is for those desiring a heavy gauge door offering improved security with the low maintenance inherent in a door with no moving parts · greater tamper resistance · increased rigidity · improved performance with built-in locks each door has a patented deep drawn stainless steel pocket handle vertical.pan horizontal.pan with an integral door pull the doors can be locked with a conventional padlock using the padlock staple protruding through the recessed handle recommended or with a built-in lock bracket support braces the hasp against the locker side panel for greater tamper resistance anti-pry lug defeats prying attempts by capturing the door flange and preventing separation from the door channel side stiffener this full-depth stiffener prevents frame channel and side-sheet torquing during break-in attempts for use at left ends of 24 gauge k.d bodies of 1 2 tier lockers with combination locks only size inches single tier 60 opening ht cat no 72 opening ht cat no 6e6 double tier 30 opening ht 60 overall ht cat no 6e 36 opening ht 72 overall ht cat no 6e3 3 tier 20 opening ht 60 overall ht cat no 6e407 24 opening ht 72 overall ht cat no 6e49 w d 5 6e3 6e63 6e3 6e33 6e409 6e4 doors shall have a catch to retain unlocked doors 8 6e5 6e65 6e5 6e35 6e4 6e43 in the closed position locking shall be accom 6e7 6e67 6e7 6e8 6e449 6e499 plished by an 11 gauge lug welded to the locker 4 6e68 6e0 frame the lug shall include a surface for the bolt 5 6e9 6e69 6e7 6e39 6e45 of a built-in combination or key lock to engage a 5 5 6e 6e7 6e9 6e4 6e45 6e47 padlock staple shall protrude through the 22 gauge 5 8 6e3 6e73 6e37 6e43 6e453 6e49 pocket the hasp assembly shall include an addi5 6e5 6e75 6e57 6e45 6e455 6e437 tional lug that mechanically engages a slot on the 8 5 6e49 6e79 6e79 6e59 latch side door formation preventing the spreading 8 8 6e3 6e8 6e8 6e47 of the door from the frame channel a separate 8 6e33 6e83 6e83 6e49 bracket shall be field installed to brace the lock 8 4 6e35 6e85 6e85 6e50 hasp assembly against the locker side to prevent twisting of the frame rubber door silencers shall note order guardian single point latch lockers by the frame overall heights do not include legs be firmly attached to the locker frame for safety purposes we strongly recommend that all lockers be either floor or wall anchored 5 6e

[close]