Catalog: 2003/2004 Buyers Guide Screw Program
Company/Brand: Powers Fasteners
timber to timber in 2003/2004 Buyers Guide Screw Program by Powers Fasteners
and engineer. Powers Commitment to specialist anchors technology provide ... screws for fixing into metal from 1.0mm to 6.4mm. A wide range of head styles to ... 4 ALZIN TYPE 17 Self drilling into timber. The special slot is designed to cut a ... thread and remove the cut timber. The point can pierce thin steel also, ... up to 0.6mm. Coatings: Zinc yellow Class 3 ... 4 ALZIN SS 304 CHIPBOARD A general timber to timber and timber to chipboard ... can pierce thin sheets of metal, up to 0.6mm. Available in fine and course ... Class 3 ALZIN No.5 POINT Designed to drill through steel up to 12.5mm thick ...
5 Self drilling screws for metal up to 12.5mm 25 26 TYPE 17 Range Self ... drilling screws for timber HEX, WAFER, CSK, BUGLE BATTEN 28 ... 35 NEEDLE POINTS Timber and light metal HEX, BUGLE, BUTTON, ... PAN CSK SERRATED 36 40 CHIPBOARDS Timber to timber CSK 6 RIBS SELF EMBEDDING ... 41 44 PK4 Self drilling roofing screws to fix through polyester insulation 26 ... rod hanging system for steel, timber and concrete 46 47 SFS Range Self ... DRIVERS 48 TECHNICAL DATA 49 55 HOW TO ORDER 56 Contents ...
up the thread during installation, to maintain a constant, effective barrier ... high quality ALZIN4 coating conforming to AS3566 Class4, providing superior ... corrosion resistance in the toughest of conditions. A unique oversized top ... roof sheet. Available for fixing into timber and metal PolykwikR or PK4 is a 100% ... sheeting through polyester insulation to steel and timber structures. Roofers ... want to be able to keep their roofing screws together so ...
or without sealing washers. Mainly used to fix metal roofing and cladding, but has ... installation of plasterboard sheeting to light gauge metal. The smooth curved ... light cement sheeting, chipboard and timber, allowing the head to sit below the ... for the fixing of secret fix brackets to timber battens or steel purlins. Points ... HEAD Countersunk head for gener al timber to timber fixing where flush finish is ... . The flat underside is ideal for metal to metal surfaces that are also flat. A ... recess or square drive can be used to install this fixing. The square drive ...
material and application, SDS point, up to 14 gauge, will drill through steel to 6 ... Type 17 Self drilling point for fixing timber without the need to predrill. Slot at ... cutting edge which reduces splitting of timber. It will penetrate thin sheet metal also ... and fixing through light gauge metal up to 0.6mm, without predrilling. CHIPBOARD ... Designed for timber to timber applications. The combination of a ... has a long extended self drilling point to drill and thread into metal up to 12. ... CSK screws will cut a clearance hole in timber. As the SDS point drills through the ... break off, the thread is formed and the timber is secured, all without the need for ...
Pty Ltd Type17 Self drilling screws for timber and thin steel to 0.60mm Head type ... int HEX 33 34 NEEDLE POINT Fastening to light steel up to 0.6mm maximum Head ... h 39 NOTE: Gauge and thread pitch need to be considered when fixing into timber ... SDS screws available. Please refer to page number for Quick reference guide ...
Architectural self tapping fastener for timber structure TW-S Lap-lox stiching ... Self drilling fastener for FC panels to timber structure SCF range Self ... drilling fastener to timber structure SXW, SW-S, SW Quick reference ... . Drilling into a steel thickness of up to 14mm is possible in one operation with ...
fromthepoint 3Threads How to measure the length of self drilling ... bugle type heads are measured from the TOP of the head to the end of As a rule, ... protruding behind the are fastening to. Embedmentintotimber Embedment into ... timber should be as follows: Gauge Minimum ... 14 6.3 1/4 Material/Type RPM Metal 2500 Timber Type 17 1500 Stainless steel 900 ...
for steel Mechanical properties for timber Protective coatings AS3566-2002 ALZIN ... These four class categories are a guide to what protective coating is required to ... where the environment changes due to location and condition . Listed below ... is a guide to these areas to assist you in choosing the right ... Class 3 There are many other factors to consider when choosing the right ... surf including the distance involved to within approx. 100m or more, high and ... stacks including the distance involved to within more , smell of chemicals in the ... for you , our valued customer . Fixing to Grade G450 Gauge Threads per inch Min ... axial force for withrawal kN Min torque for torsional strength Nm 10 16 2.5 6.9 ... 9 24 11.3 14 10 3.1 14.1 20 17.6 Fixing to timber F5 radiata pine Gauge Threads ...
/Neo SDS 12 14 x 35/37 Hex/Neo SDS Soft timbers 12 11 x 25 Hex/Neo Type 17 12 11 x 65 ... Hex/Neo Type 17 Hard timbers 12 11 x 25 Hex/Neo Type 17 12 11 x 50 ... /Neo SDS 12 14 x 45/48 Hex/Neo SDS Soft timbers 12 11 x 25 Hex/Neo Type 17 12 11 x 65 ... Hex/Neo Type 17 Hard timbers 12 11 x 25 Hex/Neo Type 17 12 11 x 65 ... /Neo SDS 12 14 x 45/48 Hex/Neo SDS Soft timbers 12 11 x 25 Hex/Neo Type 17 12 11 x 65 ... Hex/Neo Type 17 Hard timbers 12 11 x 25 Hex/Neo Type 17 12 11 x 65 ... 10 16 x 16/22 Wafer SDS Class 3 Soft timbers 12 10 x 25/35 Wafer Type 17 Class 3 ... Hard timbers 12 10 x 25/35 Wafer Type 17 Class 3 ... profiles and on insulation Please refer to roof sheet manufacturers specifications ...
metal Screw is not at the right angle to the material Keep power tool at 90 ... Not enough downward pressure on power tool Apply more downward pressure on tool ... a firm weight over screw then commence to start tool Power tool could be in ... reverse Move to forward position 2 Screws sway from ... side to side preventing a start Tip Socket ... drilling but will not threadMaterial too thick Check thickness of material Lack ... of power to tool Check correct RPM on drill check for ... further forward for right setting Torque clutch set wrong Reduce torque setting ... No clutch torque tool being usedSelect right power tool for ... product 5 Screw starts to drill hole but struggles to complete ... Try another area in the steel Steel to thick for screw Review screw and ...
or not lasting Check depth locator /torque settingAdjust to suit , keep pressure ... firm on screw head 10 Timber riding up thread when using wing SDS ... Wings breaking off too early Less pressure or slower speed ... Wrong screw being used Cement sheet too hard Head or drive damaged Screw ... embedding too deep Make sure screw has enough thread ...
