Gas Fastening 06/11 by Powers Fasteners

More catalogs by Powers Fasteners | Gas Fastening 06/11 | 21 pages | 2015-02-03

Ads

Contacts for Powers Fasteners

Powers Fasteners
2 Powers Lane
Brewster, NY 10509

P: 800-524-3244
F: 877-871-1965
Email: info@powers.com or engineering@powers.com
http://www.powers.com/

Gas Fastening 06/11 is listed under these categories

Industrial Supply > Fasteners & Hardware

Featured catalog pages of Gas Fastening 06/11

gas fastening product information functioning of gas actuated fasteners continued functioning in steel the load capacity of a gas actuated fastener when installed into steel base materials is based on the following factors 1 thickness of the steel 2 tensile strength of the steel 3 shank diameter of the fastener 4 depth of point penetration through the steel 5 fastener spacing and edge distance when a gas fastener is driven into steel it displaces the steel laterally 360 degrees around the shank of the fastener since steel is an elastic material it presses back against the shank of the fastener to hold it in place as the diameter of the fastener shank is increased the load capacity obtained will generally increase provided the steel thickness is sufficient to accept the fastener to further increase fastener performance in steel some fasteners have a knurled shank which allows the steel to form a key lock into the grooves to provide higher capacities than those obtained with a smooth

gas fastening product information design recommendations for concrete edge distance allowable load capacities the allowable load capacity which may be applied to a gas fastener is based on applyinga safety factor to the average ultimate load capacity obtained from testingaccordingto astm standards e 488 and e 1190 one purpose of the safety factor is to allowfor field variations which may differ from the testing conditions in the laboratory an example is the type and strength of the base material for proper performance gas fasteners must be installed by properly instructed operators in concrete and masonry materials the values for allowable loads are based on applyinga safety factor of 5:1 or greater to the ultimate loads loads are based on testingfasteners installed in base materials havingthe designated strength at the time of installation values are for the fastener only connected parts must be investigated separately due to the variability of gas fasteners installed in concrete or

gas fastening product information gas fastening selection guide standard pins smooth shank with rolled point standard pins with break free collation smooth shank with rolled point perma-seal coated standard pins plywood to steel spiral knurl shank with rolled point bullseye pins step shank with rolled point stick-e pin step shank straight pin smooth shank striahgt pin smooth shank straight pin knurled shank straight pin tapered shank steel pins step shank pins coated step shank pins acq page 362 362 362 362 362 362 362 366 366 366 366 366 366 366 legend â–  diameter inches pin dimensions trak-it c4 product â–¡ suitable trak-it c3 pins 1/2 steel pin step shank with rolled point may be suitable pin category length inches 0.102 0.102 0.088 0.102 0.102 0.102 0.102 0.102 0.102 0.102 0.145 0.145 0.137 0.120 0.120 0.120 0.102 0.145 0.145 1/2 3/4 3/4 1 1-1/4 1-1/4 1-1/2 1-1/2 â–  concrete â–  3/4 1 3/4 1 11/16 0.780 1-1/4 1-3/8 3/4 1

trak-it® c3 product information performance data allowable load capacities for trak-itc3 fasteners installed in normal-weight concrete1 shank diameter in mm min embed in mm 0.102 2.59 5/8 15.9 3/4 19.1 7/8 22.2 1 25.4 minimum concrete compressive strength f´c min min edge 2,000 psi 13.8 mpa 3,000 psi 20.7 mpa 4,000 psi 27.6 mpa 5,000 psi 34.5 mpa spacing distance in tension shear tension shear tension shear tension shear in mm lbs lbs lbs lbs lbs lbs lbs lbs mm kn kn kn kn kn kn kn kn 4 101.6 4 101.6 4 101.6 4 101.6 3 76.2 3 76.2 3 76.2 3 76.2 70 0.31 80 0.36 80 0.36 80 0.36 80 0.36 130 0.58 160 0.71 190 0.85 75 0.33 105 0.47 105 0.47 105 0.47 90 0.40 170 0.76 190 0.85 210 0.93 80 0.36 130 0.58 130 0.58 130 0.58 100 0.44 210 0.93 220 0.98 230 1.02 85 0.38 155 0.69 155 0.69 155 0.69 110 0.49 250 1.11 250 1.11 250 1.11 1 allowable load capacities listed are calculated using a safety factor of 5.0 or greater consideration of safety factors of 10 or higher may be necessary

trak-it® c3 product information performance data allowable load capacities for trak-it c3 fasteners installed in concrete masonry units1,2 shank diameter in mm min embedment in mm minimum spacing in mm minimum edge distance in mm 0.102 2.59 7/8 22.2 1 25.4 4 101.6 4 101.6 3-3/4 95.3 3-3/4 95.3 hollow or grouted any location f´m ≥ 1,500 psi 10.4 mpa tension lbs kn shear lbs kn 65 0.29 65 0.29 80 0.36 120 0.53 1 allowable load capacities listed are calculated using a safety factor of 5.0 or greater consideration of safety factors of 10 or higher may be necessary depending on the application such as life safety or overhead 2 tabulated load values are for fasteners installed in minimum 6-inch wide minimum grade n type ii lightweight medium and normal-weight concrete masonry units conforming to astm c 90 the face shell thickness of the concrete masonry units shall be a minimum of 1-1/4 inch allowable load capacities for trak-it c3 fasteners installed in astm a 36 steel1,2,3

product information trak-it® c4 trak-it® c4 high performance gas fastening system product description section contents the trak-it c4 and c4ex gas fastening systems were developed for use in high volume production applications powerful rugged tools for fastening wood to concrete or steel the systems are designed for speed increased power and durability the c4 cz tool was designed for use with single shot powder pins together with gas fastening technology operation of a gas fastening system does not require licensing general applications and uses general information tool specification performance data pin specifications ordering information • attaching wood to concrete block or steel • attaching steel to concrete block or steel • attaching plywood to steel • attaching steel track to concrete features and benefits no licensing required increased power and durability handles up to 2-9/16” length fasteners each fuel cell contains enough gas to

trak-it® c4 product information performance data 1 allowable load capacities for trak-it c4 fasteners installed in astm a36 steel minimum fut 58 ksi fastener type style 1/2 steel pin .680 steel pin .730 steel pin 1 steel pin 1-1/4 steel pin 2 steel pin 2 steel pin acq shank diameter inches mm minimum spacing inches mm 0.120 3.05 0.120 3.05 0.120 3.05 0.145 3.68 0.145 3.68 0.145 3.68 0.145 3.68 1 25.4 minimum edge distance inches mm minimum steel member thickness inches mm tension lbs kn shear lbs kn 1/4 6.4 245 1.09 270 1.20 330 1.46 360 1.60 390 1.73 240 1.06 170 0.75 100 0.44 170 0.75 235 1.04 360 1.60 310 1.38 280 1.24 280 1.24 1/2 12.7 1 allowable load capacities listed are calculated using a safety factor of 5.0 or greater consideration of safety factors of 10 or higher may be necessary depending on the application such as life safety or overhead allowable load capacities for c4 coated step shank acq pin in normal-weight concrete 1,2 minimum concrete compressive strength

gas fastening product information ordering information c4 pins straight and taper pins cat no shank diameter description 3/4” pin 1” pin 3/4 straight shank pin 1” straight shank pin 2-1/4” pin 2-1/2” pin 2-9/16” taper pin 2-9/16” taper pin w washer .500 pin k .680 pin k .730 pin k 1-1/4” pin 1-1/2” pin 1” wood steel pin k 1-1/4” wood steel pin k 2” wood steel pin k 55111 55113 55130 55132 55124 55128 55145 55147 55161 55163 55165 55116 55118 55172 55173 55174 standard box standard ctn 0.102 0.102 0.145 0.145 0.102 0.102 0.137 0.137 0.120 0.102 0.120 0.102 0.102 0.145 0.145 0.145 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 800 shank diameter standard box standard ctn 0.145/0.102 0.145/0.102 0.145/0.102 0.145/0.102 0.145/0.102 0.145/0.102 800 800 800 800 800 800 4000 4000 4000 4000 4000 4000 shank diameter

gas fastening stick-eâ„¢ product information accessories for trak-it c3 product description the stick-e fastening system uses trak-it c3 gas technology with specially designed accessories for fastening typical applications encountered by electricians and mechanical contractors the stick-e fastening system allows direct fastening through the fixture with the magazine pin and accessory eliminating the need for drilling or anchoring applications guide cable tie donut application for attaching small and large diameter cable ties to all types of walls and ceilings including wood steel beams concrete and block ideal for strapping wires and cable for hanging temporary lighting fixtures from all base materials fits ties up to 1/4 wide contractor s electricians suggested pin size s 780 trak-it step shank pins mini conduit clip application for attaching conduit and piping to steel beams wood and concrete ceilings contractor s electricians suggested pin size s 780 trak-it step shank pins

gas fastening product information performance data ultimate load capacities for stick-e accessories installed with 780 pin into concrete concrete block or lightweight concrete over steel deck1,2 stick-e conduit clip bx clip bridal ring cable tie insulation washer rebar clip strap washer rod hanger right angle clip minimum embed depth hv in mm 3/4 19.1 3/4 19.1 3/4 19.1 3/4 19.1 3/4 19.1 3/4 19.1 3/4 19.1 3/4 19.1 3/4 19.1 ultimate load tension lbs kn shear lbs kn 80 0.35 60 0.27 80 0.35 70 0.31 325 1.44 200 0.89 50 0.22 60 0.27 300 1.33 400 1.78 275 1.22 275 1.22 275 1.22 400 1.78 420 1.86 n/a 300 1.33 400 1.78 1 the values listed above are ultimate load capacities which should be reduced by a minimum safety factor of 5.0 or greater to determine the allowable working load consideration of safety factors of 10.0 or higher may be necessary depending on the application such as life safety or overhead 2 minimum 2,000 psi concrete or concrete block at time of installation ultimate load

gas fastening product information ordering information stick-e mini conduit clip cat no 55064 55066 55068 description mini conduit clip 1/2 mini conduit clip 3/4 mini conduit clip 1 standard box 100 100 100 standard carton 1,000 1,000 1,000 standard box 100 standard carton 1,000 standard box 100 100 100 standard carton 1,000 1,000 1,000 standard box 100 standard carton 1,000 standard box 100 100 100 standard carton 1,000 1,000 1,000 standard box 100 standard carton 1,000 standard box 100 100 standard carton 1,000 1,000 standard box 100 standard carton 1,000 standard box 100 standard carton 1,000 standard box 100 standard carton 1,000 standard box 100 standard carton 1,000 standard box 100 standard carton 1,000 standard box 100 standard carton 1,000 stick-e cable tie donut cat no description 55076 cable tie donut stick-e conduit clip one hole strap cat no 55059 55061 55063 description conduit clip 1/2 conduit clip 3/4 conduit clip 1 stick-e bx clip cat no description 55054