Page 3 of Proform 2005 Factory Performance Parts by Proform Parts

GM-Licensed Product Chrome Parts www.proformparts.com 1-586-774-2500 1 SUPER-LIGHT, FABRICATED ALUMINUM VALVE COVERS These precision welded fabricated aluminum valve covers are offered in two designs: For racing with no holes, and for street (where permitted) with the traditional 1.22" hole and GMdesigned baffle. Fits all small-block Chevrolet engines from 1958 through 1986 with flange mounting bolt holes. Two covers per box. They have recessed Bowtie and CHEVROLET Emblems, inlaid with classic Chevrolet red, billet mounting rails for maximum leak resistance, and weigh approximately 3 lbs (45%) less than stamped steel die-cast pairs! 141-800........Clear anodized, no baffle (shown above) 141-801........Clear anodized, with baffle grommets 141-802........Black, no baffle 141-803........Black, with baffle grommets (shown above) Dress-Up Kits For Chevrolet Small-Block V8, 1958-86. Includes two short baffled Bowtie valve covers, plus Bowtie timing chain cover with GM production oil seal installed, two black/red Bowtie 4wire looms, one Bowtie push-in air breather, oil dipstick, timing tab for 8" Balancer, and two grommets (air breather cap and PCV). 141-001 ........Kit w/ Timing Cover Includes two short baffled Bowtie valve covers, plus eight Bowtie valve cover wing nuts, four valve cover hold-down clamps, two black/red Bowtie 4-wire looms, one Bowtie pushin air breather cap, oil dipstick, and two grommets (air breather cap and PCV). 141-002........Kit w/ Wing Nuts Die Cast Valve Covers These premium valve covers are die-cast aluminum, manufactured to GM specifications, equipped with internal oil drippers (small-block only) and GM-designed baffles. They have recessed Bowtie and CHEVROLET Emblems, inlaid with classic Chevrolet red. All valve covers sold in pairs. For Chevy small-block V8, 1958-86. 141-108........Polished 141-116........Black Crinkle 141-117........Chrome Plated For Chevy big-block, 1965 later, tall. 141-142........Polished 141-141........Black Crinkle 141-140........Chrome Center hold-down. Tall. Supplied with mounting bolts, stainless steel rubber washers (also available separately below as 141-133). All valve covers sold in pairs. For Chevy small-block V8, 1987 later. 141-130........Polished 141-131........Black Crinkle 141-132........Chrome Plated Bolt Washer Kit 141-133........Bolt Washer Kit (8) Stamped Valve Covers These CHEVROLET Bowtie valve covers are made of heavygauge steel, 20% thicker than typical aftermarket valve covers, greatly reducing the likelihood of leakage around the valve cover flange area caused by fasteners being over-torqued. The chrome plating meets GM quality specifications. All valve covers bear the powerful Bowtie and CHEVROLET Emblems. Black crinkle valve covers, with their distinctive look and boldly striking Bowtie and CHEVROLET Emblems, inlaid with classic Chevrolet red, are CED painted for long-term corrosion resistance, and then black crinkle painted on the outer surface. Stamped valve covers are offered in either tall or production height (short). Oil restricting baffles are offered in many valve covers for those who wish to maintain the PCV hookup. All valve covers are sold in pairs, equipped with air breather and PCV grommets, unless specified otherwise. Technical Note: Production height Chevy small-block valve covers and valve covers with baffles will not clear most stud girdle applications. Chevy small-block or S/B refers to 1958-1986 engines, unless otherwise specified. B/B refers to big block engines. For Chevy small-block V8,1958-86. 141-102........Short, with baffle 141-103........Tall, with baffle 141-101........Tall, no baffle 141-750........Short, with baffle, Black Crinkle 141-751........Tall, with baffle, Black Crinkle For Chevy small-block V8, 1987 later. 141-107........Center hold-down For Chevy big-block, 1965 later. 141-114........Short, with baffle 141-115........Tall, with baffle 27-2401-51955

[close]