Catalog: Spherical Plain Bearings
Company/Brand: RBC Bearings
bearing shaft shoulder in Spherical Plain Bearings by RBC Bearings
spherical plain bearings radial inch ° bckdd1 d r1 30° series b ... /0.014 0.009/0.014 0.009/0.014 d1 tilt shaft shoulder angle 1 dia deg 0.563 0.703 0. ... dimensions are in inches outer rings of bearings size 72 and above are double fractured ...
spherical plain bearings radial metric b ° ckdd1 d r1 r2 30° ... 0.17/0.30 0.17/0.30 0.20/0.34 d1 tilt shaft shoulder angle 1 dia deg 16 18 21 25 30 ... are in millimeters outer rings of bearings size 160 and above are double fractured ...
quadlubeŽ long life spherical plain bearings inch series b lssq part number sealed ... 0.009/0.014 0.009/0.014 0.009/0.014 d1 shaft shoulder dia 0.844 0.984 1.125 1.406 1. ... dimensions are in inches outer rings of bearings size 72 and above are double fractured ...
quadlubeŽ long life spherical plain bearings metric series mb ssq part number ... /0.30 0.17/0.30 0.17/0.30 0.20/0.34 d1 shaft shoulder dia 21 25 30 35 41 47 51 57 68 ... are in millimeters outer rings of bearings size 160 and above are double fractured ...
spherical plain bearings high misalignment inch b ° ckdd1 d r2 ... /0.009 0.005/0.009 0.005/0.009 d1 tilt shaft shoulder angle 1 dia deg 1.66 1.95 2.22 ... dimensions are in inches outer rings of bearings size 72 and above are double fractured ...
spherical plain bearings high misalignment metric b ° ckdd1 d ... 205 210 c k d1 outer ring sphere tilt shaft width dia unmounted shoulder angle ... are in millimeters outer rings of bearings size 160 and above are double fractured ...
spherical plain bearings extended inner ring inch ° bckdd1 d 30 ... 6.750 7.500 8.250 k c d1 outer sphere shaft ring dia unmounted shoulder width ... dimensions are in inches outer rings of bearings size 72 and above are double fractured ...
spherical plain bearings extended inner ring metric ° bckdd1 d ... /0.17 0.10/0.20 0.10/0.20 0.10/0.20 d1 shaft shoulder dia 21 25 30 35 41 47 51 57 68 ...
/0.014 0.009/0.014 0.009/0.014 d1 tilt shaft shoulder angle 1 dia deg 0.844 0.984 1. ... dimensions are in inches outer rings of bearings size 72 and above are double fractured ...
2.070 1.969 3.375 2.318 2.187 3.750 d1 shaft shoulder diameter ref 0.844 0.920 0.984 ... in inches consult rbc engineering for bearings with tapered bore 46 ...
2.2494 2.2494 2.2494 2.4994 2.4994 d1 shaft shoulder diameter ref 0.844 0.920 0.984 ... in inches consult rbc engineering for bearings with tapered bore 48 ...
more radial bearing designs with few exceptions steel-on- ... steel spherical plain bearings used in dynamic applications must be ... area between inner and outer ring if a bearing is subject to a unidirectional load it ... eventually exit without benefiting the bearing service life the quadlubeŽ design ... solves the lubricant flow problem of bearings where the load acts always in the same ... into the contact area even with the bearing under load the grooves help to collect ... wear debris which is purged from the bearing during a subsequent relubrication cycle ... bore inner rings rbc quadlubeŽ design bearings with heavy section inner rings are also ... 2 main reasons for using a tapered bore bearing ˇto prevent rotation between inner ring ... bore and shaft ˇto control the diametral clearance of ... the bearing assembly as the inner ring is forced up ...
fa ps hardened spacer d d1 ps fa shaft design figure 18 reduce contact ... tapered spacer with the exception of bearings under light load and press fitted inner ... rings it is generally recommended that shafts or pins be heat treated to a surface ... takes place between inner ring and shaft under very heavy loads even an ... the inner ring will not rotate on the shaft thrust loads on radial bearings are ... yield strength in compression of the shaft material or any spacer which may be ... it may be necessary to harden the shaft shoulder to prevent plastic deformation ... with a tapered od may be used if the shoulder cannot be heat treated figure 18 ... standard rbc spherical plain bearings are phosphate treated and coated with a ... if used in a dynamic application the bearings must be lubricated with oil or grease ...
