Page 58 of Devices for Automotive by Sanken Electric Co., Ltd.

Electrical Characteristics Parameter Symbol min typ max Unit Conditions Ratings Power MOS FET output leakage voltage High-side Power MOS FET output on-state voltage Power MOS FET output breakdown voltage Delay time BVOUT IO=0.4A, VIN=10V VO=500V IO=100m A VCC=10V, VM=400V VCC=6 to 15V VCC=10A, VIN=10V, VM=85V, IO=0.41A VCC=6 to 15V V 500 0.18 0.26 100 m A 0.34 V 4.0 mA 0.8VCC V 2.0 V m s 0.2VCC 6 V IOUT (off) VOUT (on) Lowside Power MOS FET output on-state voltage IO=0.4A, VGL=10V 0.18 0.26 0.34 V VOUT (on) Quiescent circuit current VCC=6 to 15V VCC=10V, VM=400V 3.0 4.0 mA mA ICC 1 ICC 2 ICC 3 VIH VIL td (on) 3.0 m s td (off) -40 to +125 C 15 VCC Input voltage (Low level) Operating voltage Operating circuit current Input voltage (High level) Parameter Symbol Unit Conditions Ratings Absolute Maximum Ratings Power source voltage Input voltage Output voltage Output current Power dissipation Storage temperature Operation temperature VM VIN VO IO PD Tstg Topr V V V A W A W Tc=25 C Without heatsink With infinite heatsink C C 500 15 500 7 IO (peak) 15 5 (Ta=25 C) 40 (Tc=25 C) -40 to +125 -40 to +125 Junction temperature Tj C 150 * 56 Features l One Package Full Bridge Driver Consisted of High Voltage IC and Power MOS FETs (4 pieces) l High Voltage Driver which accepts direct connection to the input signal line l External components such as high voltage diodes and capacitors are not required High Voltage Full Bridge Drive IC SLA2403M * Power GND (D terminal) to -HV (-HV terminal) voltage. * Block Diagram * Dotted Line: Outside Connection 4 3 5 2 6 8 10 9 11 13 17 14 16 15 D2 7 OUT1 OUT2 GL1 GL2 HO2 LO2 HO1 MIC CPU VCC VIN1 VIN2 -HV LO1 D1 MOSQ1 MOSQ2 MOSQ'1 MOSQ'2 L GND VIN1 0V 0V 10% 10% 10% 10% VOUT1 td (on) td (on) 10% 10% 10% 10% VIN1 0V 0V VOUT2 td (on) td (on) Highside switch turn-on, turn-off Lowside switch turn-on, turn-off * About delay time Signal input waveform vs output waveform * D t: D t =td (on) td (off) Measurement Circuit VIN1 VIN2 VM VOUT1 VOUT2 VIN2 VIN1 RL Conditions VCC=10V, VIN=10V (pulse) VM=85V IO=0.41A (RL=207W ) 1 2 External Dimensions (unit: mm) 31.0 0.2 4.8 0.2 1.7 0.1 24.4 0.2 16.4 0.2 2.45 0.2 Ellipse 3.2 0.15 3.8 3.2 0.15 17 P1.68 0.1=28.56 31.5 max 0.65 +0.2 -0.1 +0.2 -0.1 +0.2 -0.1 1.0 0.55 Timing Chart VCC IN1 IN2 HO1 HO2 LO2 LO1 OUT2-GND HV 0V -400V -100V OSC 400Hz Ignition a: Part No. b: Lot No. a b PW 250m s * When pulse signal is inputted to VlN1, RL on solid line is ON and dotted line RL is off. On the contrary, when pulse signal is inputted to VlN2, RL on dotted line is ON and dotted line RL is off.

[close]