8 results for syringe filter ptfe found in 0.000 seconds

removal samples for hplc membrane filters have established themselves as the ... filters of choice for particle removing ... to use minisart rc and minisart srp syringe filtration units are available in both ... removal from the box the combination of ptfe filter holders and ptfe membrane ... filters is particularly suitable for the ... particle removal using 0.45 µm membrane filters is described in the respective ... as well as using 50 mm membrane filters in glass or stainless steel vacuum ... filter holders difficult to filter samples such as sludge samples must be ... for cell counters the all-glass filter holder with a 0.45 µm membrane filter ... as shown in the guide below smaller filters must be inserted for the removal of ... units prevent this blockage by filtering in the opposite direction of the ...

units with a clean and chemically inert ptfe membrane ready-to-use units for simple ... 25 for up to 100 ml applications for syringe filter holders specifications for ... srp4 minisart srp15 minisart srp25 filter diameter filter area housing burst ... housing polypropylene-reinforced ptfe membrane filter 121°c 30 min autoclave ...

re-usable 13 mm syringe filter holders for the ultracleaning of small ... volumes up to about 10 ml ptfe holder for solvents and chemicals made ... completely of ptfe this holder is unaffected by chemicals ... could be released into the liquid being filtered it is therefore extremely well suited ... and avoids twisting of the membrane filter when the top is tightened onto the base ... applications for syringe filter holders specifications for the 13 mm ... ptfe syringe filter holder connectors chemical ... 100 kpa 14.5 psi with 0.2 µm membrane filter with 0.45 µm membrane filter filtration ... max operating pressure membrane filter diameter sterilization hold-up volume ... luer lock inlet luer slip outlet as for ptfe approx 10 ml/min 18 ml/min 0.5 cm2 13 g ... ptfe top and bottom part 5 bar 500 kpa 72.5 ...

re-usable 25 mm syringe filter holders for the ultracleaning and ... holder for solvents and chemicals the ptfe-coated surface on the top part is an important ... property of the filter holder and ensures leak-proof sealing ... depends only on the inserted filter type filtration the top part can easily ... part using the enclosed tightening tool filter supports in the top and bottom parts ... in either direction applications for syringe filter holders specifications for the ... 100 kpa 14.5 psi with 0.2 µm membrane filter with 0.45 µm membrane filter membrane ... filter filtration area materials female luer ... slip outlet as for stainless steel and ptfe approx 45 ml/min 80 ml/min 80 ml/min ... with 0.45 µm membrane filter 3 cm2 stainless steel 1.4305 top and ... bottom parts ptfe-coated sealing area in top part luran 368r ...

with barrels to hold the liquid to be filtered can be connected to a pressure source ... bottle after insertion of the membrane filter and prefilter and if necessary after ... and mini cartridge housings the filterable liquid must be fed in on the inlet side ... thread with inlet hose nipple using a ptfe-tube 16999 or a capsule with inlet hose ... to a pressurized container using the ptfe pressure hose 16999 the hose nipple can ... no 16881 in order to use the device as syringe filter holder a luer slip connector ... the flexible pressure hose 17091 or the ptfe pressure hose 16999 for the filtration ... of easy-to-filter largevolume liquids the 47 mm holder ... a connector with g3/8 male thread and a ptfe pressure hose 6 for stainless steel ... to a pressurized container with the ptfe hose 16999 however it is connected ...

units with naturally hydrophobic ptfe membrane for reliable sterile venting ... up to 3 bar 43.5 psi the 20 cm2 large filter area allows high flow rates at low ... of a polyesterstrengthened 0.2 µm ptfe membrane in a cyrolite housing with ... inner diameter with slip-fit for luer syringes or 1/8 male npt all materials pass ... for 0.45 µm 20 cm2 approx 3 ml 62 mm ptfe membrane filter aus ptfe reinforced ... m biosafety bubble point air flow rate filter area filling volume housing diameter ... minisart hy bubble point air flow rate filter area housing burst pressure water ...

for professional meters accessories for syringe filter holders accessories for vacuum ... filter holders accessories for vacuum filter holders and manifolds accessories for ... systems cellulose acetate membrane filters type 111 cellulose nitrate ester ... membrane filters centrifuges centrisart® centrifugal ... chemical compatibility table for filter holder cartridge and o-ring materials ... chemical compatibility table for filter materials and mini cartridges chemical ... dishes docuclip® docu-phmeter dosing syringe expand® ­ biotechnology workshop expand ... name facts® service program films filter holders and manifolds filter integrity ... testing systems filter papers gelatine membrane filters glass ... for vacuum filtration gridded membrane filters for colony counts gridded membrane ...

and analytical balances media membrane filters for liquid samples membrane pump ... mikro-dismembrator minisart 0.2 µm syringe filter units minisart gf syringe filter ... containers and bottles minisart plus syringe filter units minisart rc syringe filter ... units minisart srp syringe filter units minisart standard syringe filter ... pipette calibration polyamide membrane filters type 250 polycarbonate holders 47 mm ... polycarbonate track-etchmembrane filters type 230 polyethersulfone membrane ... filters type 154 potter s pressure filtration ... purification by membrane adsorbers ptfe filter holder 142 mm for pressure ... filtration ptfe filter holder 47 mm for pressure filtration ... regenerated cellulose acetate membrane filters type 184 re-usable sterility test ...