Catalog: Wood Construction Connectors 2006 Catalog | |
| and through the floor system with a all thread rod, a nut and washer (not ... attachment to the top of the truss, allowing installation after the roof is sheathed ... | |
| reamer and type 17 tip cuts a hole to allow installation without predrilling. ... 3 Fasteners per Carton Spruce-Pine-Fir Allowable Loads 1 Doug Fir-Larch/Southern Pine ... Allowable Loads 1 14 ga to 3 ga 13 14 ga to 3 ga ... .S. Patent 6,109,850 Identification on all SDS screw heads (SDS x3 shown) unless ... 14 wood screw or tested ultimate/5. If thread penetration into main member is less ... than thread length T as shown in table, reduce ... allowable load by 172 lbs. x inches of thread not in main member. Use 121 lbs./inch ... be increased any further than shown. 1. Allowable loads for SDS screws are based on ... on a wood thickness of 1 side member. All applications are based on full ... Spacing (in) Edge Dist. (in) Allowable lbs. Allowable lbs. Allowable lbs. ... | |
| Bolts RFBs are clean, oil free, pre-cut threaded rod, supplied with nut and washer. ... Nuts Model No. Rod Diameter H Min Allowable Tension Capacity (lbs.) (100) CNW 0. ... 2 11500 CNW 0.500 1 Code Ref. CNW Allows fast visual check for correct all ... thread rod installation HSCNW High Strength ... Nut Typical CNW Rim Joist Installation All-thread rod is correctly installed when visible ... and HSCNWs provide a positive stop to allow even bolt threading top and bottom. ... of corresponding ASTM A36 bolts and threaded rod. HSCNWs meet and exceed the ... ASTM A193 Grade B7 bolts and threaded rods. Contact factory for other coupler ... : Tighten the two rods until each all-thread rod can be fully seen in the witness ... page 12 for Code Listing Key Chart. 1. Allowable loads may be increased as permitted on ... | |
| 24 hrs 100 F 20 min 16 hrs 12 hrs WEDGE-ALL The Wedge-All is a non-bottom bearing, ... increases as tension is applied. The threaded stud version is available in nine ... available for wire supported fixtures. Threaded studs are set by tightening the nut. ... ICC ER-1056 (Titen HD); ER-3631 (Wedge-All); City of L.A. RR24682; FL 2304.2 ( ... Titen HD); FL 402.5 (Wedge-All). 29 Anchors ANCHOR SYSTEMS GENERAL ... the mixing nozzle. AT HIGH STRENGTH, ALL TEMPERATURE ADHESIVE Acrylic-Tie is a ... material. Formulated for use in all types of weather, AT is designed to ... protection. Check with factory. Wedge-All Titen HD U.S. Patent 5,674,035 6,623, ... | |
| an Anchor Systems CD-ROM which contains all of the information you need for your ... dry enviroments only. Rod Dia. (in.) Allowable Tension Loads (133) 5875 6020 5875 9555 ... ) Purlin Anchorage Adhesive Tension Allowable Loads 1. The allowable loads for the ... , mortar and grout specifications. 3. Threaded rods must comply with ASTM A307 minimum ... 4. Allowable loads may be increased to 2225 lbs for ... | |
| factor. SPECIAL FEATURES: Rolled threads for higher tensile capacity. Offset ... with maximum 24" o.c. spacing. Grout all cells with minimum 2000 psi concrete. ... Width Dia. Length Min Embed le Allowable Tension Load 1,2 Concrete 8" CMU Block ... amount of concrete cover. 4. Maximum allowable load is 8150 lbs. for SSTB28, 34 and 36 ... 7. Order the SSTBL models for longer thread length (5 ex. SSTB24L. SSTBL and SSTB ... available on SSTB14. 8. SSTB34 has 4 of thread and SSTB36 has 6 ". These two models ... Anchor Design information. 11. Allowable load for SSTB14 is 5020 lbs. when f' c ... | |
| Model No. Ga Dimensions Fasteners Allowable Tension Loads SPF/HF (133/160) Holdown ... 5 Deflection at Highest Allowable Design Load Flush W H B Anchor Dia. No ... 5 Deflection at Highest Code Ref. Allowable Design Load Raised .081 .077 .073 ... Allowable Tension Loads DF/SP (133/160) 3610 4685 ... 5860 31, 98, 122 ,140 C L 1.Allowable loads have been increased for ... durations with no further increase allowed; reduce where other load durations ... screw value. 5.Deflection at Highest Allowable Design Load: The deflection of a ... the holdown when loaded to the highest allowable load listed in the catalog table. This ... Model No. Ga W H B Anchor Dia. Allowable Compression Load 10 (lbs) No. of SDS ... Screws Holdown Deflection at Highest Allowable Tension Design Load Code Ref. HDQ8-SDS3 ... | |
| applications to transfer tension loads. All HDAs and the HD15 are self-jigging, ... , HD8A, HD10A and HD14As seat design allows greater installation adjustability. An ... Simpson gray paint. INSTALLATION: Use all specified fasteners. See General Notes ... , use a steel nylon locking nut or a thread adhesive on the anchor bolt. Bolt ... | |
| , 122 Holdown 9 Deflection at Highest Allowable Design Load Holdown 9 Deflection at ... Highest Allowable Design Load Raised Wood Member ... 8310 9540 9900 11080 13380 15305 Allowable Tension Loads DF/SP (133/160) ... Allowable Tension Loads SPF/HF (133/160) 8. See ... information. 9. Deflection at Highest Allowable Design Load: The deflection of a ... the holdown when loaded to the highest allowable load listed in the catalog table. This ... load test conducted on a steel jig. All other sources of deflection shall be in ... . 11. The Designer shall reduce the allowable loads shown per NDS requirements when ... bolt threads are in the shear plane. 12. HDA and HD ... allowable loads are based on the lower of the ... . Post design shall be by Designer. 1. Allowable loads have been increased for ... | |
| EPB Elevated Post Bases Model No. Nails Allowable Loads (DF/SP) Uplift (133/160) EPB44T 6 ... 2. Uplift and lateral loads require the threaded rod to be set in wet concrete or ... or AT Adhesive Model No. W L H Nails Allowable Loads (DF/SP) (133) and (160) D Code ... OD x 8" pipe FINISH: EPB44A Galvanized; all others Simpson gray paint (may be ... Resistance, page 6-7. INSTALLATION: Use all specified fasteners. See General Notes ... . Allows 1" to 2 clearance above concrete, 2" ... posts. MATERIAL: 12 gauge base. EPB44T Threaded rod support "x5" (shipped assembled). ... EPB44PHDG Threaded rod support "x6", nut and washer are ... FINISH: EPB44T: Base Galvanized, Threaded Rod Zinc Plate EPB44PHDG: Hot-Dip ... and adjust to the desired height. The threaded rod shall be embedded a minimum of 2 ... | |
| See SSTB anchor bolts, pages 33-34, for allowable loads and installation. Alternate ... may be required depending on load. 3. All thread rod not supplied with Raised ... of record must specify if high strength all-thread rod is required, depending on load. 4. ... All Raised Floor walls require 1 or 3" end ... will result in load reductions. 6. See allowable vertical load table below for Strong- ... Bottom of Wall Holdown 3 Anchor Bolts Allowable Shear V Load (lb) Drift at Allowable ... Shear V (in) Allowable Shear V Load (lb/ft) Wall Code Ref. ... Bottom of Wall Holdown 2 Anchor Bolts Allowable Shear V Load (lb) Drift at Allowable ... Shear V (in) Allowable Shear V Load (lb/ft) Wall Code Ref. ... See page 12 for Code Listing Key Chart. ALLOWABLE VERTICAL LOADS (lbs) C4 T1 C5 C2 C1 C3 ... | |
| FINISH: Galvanized INSTALLATION: Use all specified fasteners. See General Notes ... of the face bolt using ET22 Epoxy-Tie. All thread rods and/or machine bolts to be ... lbs (133) and 3515 lbs (160). 8. Table allowable loads were determined using test ... Down Load Code Ref 62, 123 Grouted CMU Allowable Loads Solid Concrete Allowable Loads ... 16 18 7 9 11 11 14 16 18 1.ATR is all threaded rod. 2.Allowable loads are ... wind loading with no further increase allowed;reduce where other loads govern. 4.Loads are ... -Tie 6 minimum embedment required. All thread rods and/or machine bolts to be ... to the Anchoring Systems catalog. 1. Allowable loads are based on a minimum of 2500 ... wind loading with no further increase allowed; reduce where other loads govern. 4. ... | |
| 1.The allowable loads have been increased 33% and 60% ... wind loading with no further increase allowed; reduce where other loads govern. 2.Load ... cut washer is required with the all thread rod. 4. FSCs shall be offset no more ... wall cavitities easy. Installs with a all thread rod, nut and washer (not ... : Can be used on a single 2x stud. Threaded rod, washers and nuts are not supplied ... with the FSC. Use threaded rod between 4' to 5' long, grade A307 ... to diameter hole through the plates for threaded rod access, hole should be located ... " 1830 1830 160 Model No. Ga Fasteners Allowable Tension Load Anchor (133) (160) DF/SP ... ) Model No. Depth (min) Beam Dimensions Allowable Tension Loads 3930 3380 12-10d 4440 ... | |
| two comparably sized holdowns and the threaded rod. The LFTA Light Floor Tie Anchor is ... -Simpson gray paint INSTALLATION: Use all specified fasteners. See General Notes ... full loads. Nail holes between floors allow preattachment to the joist during ... No. Ga Dimensions Fasteners (Total) Allowable Uplift Loads 1 (133) Allowable Uplift ... Code Ref. 5, 41, 85, 121 20, 80, 124 1.Allowable loads have been increased 33% and 60% ... wind loading with no further increase allowed; reduce where other loads govern. 2. ... Reduce the allowable load for the LFTA according to the code ... 795 2585 795 Model No. Dimensions Allowable Loads 1,2 Minimum Bolt End Edge ... in single shear is not load-rated. 2. Allowable loads are based on a minimum member ... | |
| FINISH: Galvanized INSTALLATION: Use all specified fasteners. See General Notes ... . MATERIAL: 12 gauge plates, threaded rod, 1 O.D. steel pipe FINISH: None. ... service life. INSTALLATION: Use all specified fasteners. See General Notes ... Loads (100) H (inches) (Min-Max) Threaded Rod Length JP44 2-4 4 4440 1 J57 5-7 ... of JP44 Installation 1. Consider allowable loads for 4x4 post. 2. Loads may not be ... | |
| W H Post Dimensions Fasteners Model No. Allowable Loads Anchor Bolt Uplift Code Ref Down ... 3 170 9 1. Allowable uplift load capacities are for solid ... Viga" (Ponderosa Pine) wood posts. 2. All allowable uplift loads are based on a ... Strong-Tie Anchor Systems catalog. Allowable uplift capacities shall not exceed ... (700 psi for Ponderosa Pine). 4. Allowable loads may not be increased for short ... . Model No. Ga Dimensions Bolts (Total) Allowable Loads 1,2,3,4 W1 W2 L D1 D2 D3 D4 Qty ... , gray paint or galvanized TO ORDER: All products with PC suffix are textured ... page 12 for Code Listing Key Chart. 1. Allowable loads have been increased 33% and 60% ... or wind loading. No further increase allowed; reduce where other loads govern. 2. ... halfway with Simpson SET epoxy. Insert all-thread rod and allow epoxy to set and cure. ... | |
