Catalog: Wood Construction Connectors 2006 Catalog
Company/Brand: Simpson Strong-Tie
hot dip galvanize standard in Wood Construction Connectors 2006 Catalog by Simpson Strong-Tie
information and lead times. Products hot-dip galvanized after fabrication (14 ga. ... increases with material thickness. Hot-dip galvanizing is available for many ... both sides). These products require hot-dip galvanized fasteners (fasteners ... galvanized per ASTM A153). Galvanized (G185) 1.85 oz. of zinc per square foot ... of surface area (hot-dip galvanized per ASTM A653 total both sides). Z-MAX ... code reports. These products require hot-dip galvanized fasteners (fasteners ... galvanized per ASTM A153). Products manufactured ... , and are available from Simpson. TM STANDARD COATING G90 (Galvanized G90) .90 oz. of ... outside the United States. The minimum standard for galvanization in the United States ... Steel fasteners. When using ZMAX/HDG galvanized connectors, use fasteners galvanized ...
Recent changes in building codes and standards have affected the way allowable loads ... Design. Building codes and material standards have traditionally allowed designers ... of steel connectors. Newer codes and standards only allow steel stress increase when ... , as long as the referenced material standard/section permits it. The ASCE7 Standards ... with building codes and steel design standards (AISI and AISC). In the past, these ... steel standards have permitted the use of a one-third ... . However, the latest editions of these standards have discontinued that practice. ... additional corrosion protection (ZMAX, Hot-Dip Galvanized or Stainless Steel). Check ... protection is provided (Z ZMAX, HDG Hot-Dip Galvanized or SS Stainless Steel). See ... all load combinations in the codes and standards covered by this catalog. For that ...
1.N16 fasteners may be ordered electro-galvanized; specify EG; for example N16EG. This ... for ZMAX or HDG applications. 2.HDG hot-dip galvanized; SS stainless steel; Bright ... mm 9.5 12.7 15.9 19.1 22.2 1 25.4 US Standard Steel Gauge Equivalents in Nominal ... thickness varies according to mill standards. Use these Roof Pitch to Hip/Valley ... Decimals (in) in mm Uncoated Steel Galvanized Steel (G90) Z-MAX (G185) 3 6.0 0.239 ...
installation for the SDS Screws. Fits a standard drill. The Simpson Strong-Drive wood ... dichromate, EG Electrogalvanized, HDG Hot-dip Galvanized. 4. SDS screws install best ...
are available uncoated or with a hot dip galvanized (HDG) finish. The BP SKT ... give greater bearing surface than standard cut washers, and help distribute the ... : See table FINISH: LBP, LBPS BP S galvanized; BP None. BPs may be ordered HDG, LBPs ... : Wedges 14 gauge, WT 18 gauge FINISH: Galvanized INSTALLATION: Use two 3 long wedges ...
For holdowns, per ASTM test standards, anchor bolt nut should be finger-tight ... openings. MATERIAL: See table. FINISH: Galvanized INSTALLATION: Use all specified ... . FINISH: Simpson gray paint. Optional hot-dip galvanized finish; see Corrosion- ...
. WMs are designed for use on standard 8" grouted masonry block wall ... , stirrup. FINISH: Simpson gray paint; hot-dipped galvanized available: specify HDG, ...
require the use of web stiffeners for standard non modified I-joist installations. See ... 104 to 113. FINISH: LBV, B, BA and HB Galvanized; all saddle hangers and all welded ... . LBV, B, BA and HB may be ordered hot-dip galvanized; specify HDG. INSTALLATION: ... for special considerations when welding galvanized steel. The area should be well- ... Simpson representative for details. Hot-dipped galvanized available: specify HDG. ...
. WMs are designed for use on standard 8" grouted masonry block wall ... , stirrup. FINISH: Simpson gray paint; hot-dipped galvanized available: specify HDG. ... psi. Web stiffeners are required for standard joist nailing configuration with these ...
by the building designer. OPTIONS: Hot-dipped galvanized: specify HDG. See Hanger ... with no drilling required. Available in standard SCL widths and made to specified ...
page 123. FINISH: Simpson gray paint. Hot-dip galvanized available; specify HDG. ... upper half of the x 1 slotted holes. Standard washers must be used with all bolts. ... See table. FINISH: Simpson gray paint. Hot-dip galvanized available; specify HDG. ...
. WMs are designed for use on standard 8" grouted masonry block wall ... and stirrup FINISH: Simpson gray paint; hot-dipped galvanized available: specify HDG. ...
. MATERIAL: See table FINISH: LFTA-galvanized; FTA-Simpson gray paint INSTALLATION: ... are not required. OPTIONS: FTA may be hot-dip galvanized; specify HDG. The standard ... nail sizes and information. FINISH: Galvanized. See Corrosion-Resistance, page 6-7. ...
give greater bearing surface than standard cut washers, and help distribute the ... . MATERIAL: 3 gauge maximum FINISH: Galvanized, textured powder-coated flat black, ... flat black paint, gray paint and hot dipped galvanized coating. OFF-THE-SHELF ... noted. Most are also available with a galvanized finish or gray primer. Check factory ...
product. Testing is performed using a standardized hanger test method. The joist in the ... gray paint. Specials that are not galvanized before fabrication can be hot-dip ... galvanized after fabrication; specify HDG. CODES: ... beyond the amount specified in the standard hanger table. Fill all holes with the ...
