Catalog: Wood Construction Connectors 2006 Catalog | |
| 0.50 f. For face-mount hangers straight straps, use 0.86 of table loads for Spruce- ... tends to split, consider pre-boring holes with diameters not exceeding .75 of ... ) must be fastened together to act as one unit to resist the applied load ( ... the product. Fill all fastener holes with fastener types specified in the ... unless otherwise specified. b. Bolt holes shall be at least a minimum of and no ... ) are properly installed in the nail holes. Tools with nail hole-locating ... | |
| reduce slip due to overdrilled bolt holes. Smaller centerline reduces eccentricity ... required to bind members to act as one unit without splitting the wood. See ... | |
| member to the center of the first bolt hole. HD6A, HD8A, HD10A and HD14As seat ... adhesive on the anchor bolt. Bolt holes shall be a minimum of to a maximum of ... required to bind members to act as one unit without splitting the wood. For ... | |
| to the center of the first stud bolt hole. End distance may be increased as ... bolt slip can occur if oversized holes are drilled through the stud for ... holdown stud bolts (oversized holes are when the hole diameter is greater ... C. When a holdown is installed on only one side of the stud, an eccentricity ... | |
| ; some models have extra fastener holes. See General Notes. Purlin Anchor must ... The minimum wall specifications are: A One #4 vertical rebar, 32" long, 16" each ... to wall anchorage using embedded straps shall have the straps attached to or ... | |
| locator line. Additional diamond hole in RJ versions. BENEFITS Built-in Tab ... removing STHD. Additional Diamond Hole: One more fastener to help prevent the ... PORTION OF STRAP HOLDOWN LOCATE ONE #4 REBAR WITHIN HATCHED AREA (MAY BE ... concrete code requirements. le LOCATE ONE #4 REBAR WITHIN HATCHED AREA (MAY BE ... , and then bent vertical (bent one full cycle) for nailing to the stud, ... | |
| strap from bottom up. Strap may be bent one full cycle. Where fewer fasteners are ... or double 2xs, either fill every nail hole with 10dx1 nails or fill every other ... nail hole with 16d commons. Reduce the allowable ... required to bind members to act as one unit without splitting the wood. ... tested concrete pullout strength (fill holes from bottom up); additional nail holes ... determined the pullout strength with one horizontal #4 rebar in the shear cone. ... by nailing to form. Installation holes allow nailing to the form, resulting in ... of the table loads. 3.Optional fastener holes provided. Calculate loads according to ... between and 8". 6. Optional fastener holes are provided on selected products. ... fasteners. 7. Strap may be bent one full cycle. (Bent horizontal 90 then ... | |
| ; some models have extra fastener holes. See General Notes. Wood splitting may ... less than 3 ", fill every other nail hole with 10dx1 nails. Reduce the allowable ... . The minimum wall specifications are: one 4 vertical rebar, 32" long, at 32" o.c ... to wall anchorage using embedded straps shall have the straps attached to or ... | |
| Girder Tiedown Retrofit MTSM/HTSM Twist Straps Model No. L Fasteners 2 Doug-Fir-Larch/ ... where other loads govern. 2.Twist straps do not have to be wrapped over the ... grouted concrete block with a minimum one #5 rebar horizontal. Minimum f I c = ... for wood installation. MATERIAL: Straps-7 gauge; Plate-3 gauge FINISH: Powder ... uplift loads to the foundation. Screw holes are configured to allow for double ... two-ply minimum truss. Only 2 of the 4 holes provided on each strap are required to ... shall not be installed in adjacent holes. Can be installed on roof pitches up to ... 3.THDs should be spaced in every other hole on the part. 4.The THDs and SDS are ... | |
| 156 Straps Ties HRS/ST/FHA/PS/HST/LSTA/LS TI/MST/ ... (hanger not shown) Bend strap one time only Typical LSTA Installation ( ... hanger not shown) Bend strap one time only CODES: See page 12 for Code ... perpendicular and parallel-to-grain. Hole diameter in the part may be oversized ... splice details, refer to T-CMST. 8. Straps with 10d (0.148 dia. x 3) nails ... | |
| 160 Straps Ties FTA/LFTA Floor Tie Anchors T and L ... use as a floor-to-floor tension tie, one FTA replaces two comparably sized ... side opposite FTA for full loads. Nail holes between floors allow preattachment to ... | |
| (DF/SP) 6. MGT can be installed with straps vertical for full table load provided ... shimming is required. Fasten to act as one unit. Before installing fasteners, ... . LGT3-SDS2.5 The four large hexagon holes are intended for CMU and concrete ... page 12 for Code Listing Key Chart. 167 Straps Ties LGT3-SDS2.5/LGT2/MGT/HGT Heavy ... | |
| 168 Straps Ties DSP/SSP/SP/SPH/RSP4 Stud Plate ... -sill plate installation-fill all round holes. DSP/SSP-top plate installation-fill ... all round and triangle holes SP-one of the 10d common stud nails is driven ... Plate Width 1. SP1, 2, 3 and SP5: drive one stud nail at an angle through the stud ... | |
| 169 Straps Ties LTP4/LTP5/A34/A35 Framing Angles ... Plates 1. Allowable loads are for one anchor. When anchors are installed on ... rim joist or blocking connections. Nail holes are spaced to prevent wood splitting ... connection types A1, E, C1. A35-Bend one time only. LTP4-Use 12-8dx1 nails. ... | |
| 171 Straps Ties A Angles and Z Clips L/LS/GA ... 121 170 1. Z28 and Z38 do not have nail holes. Fastener quantities are as required. 2 ... General Notes. LS-field skewable; bend one time only. Joist must be constrained ... | |
| and protection requirements with one strap. Nail Stoppers help prevent nails ... of the National Electric Code ...bored holes for wiring shall be 1.25" from the ... | |
