Page 115 of Wood Construction Connectors 2006 Catalog by Simpson Strong-Tie

Typical SUL Installation with Bevel Cut Joist (HSUL similar) Typical SUR Installation with Square Cut Joist (HSUR similar) 116 Engineered Wood Structural Composite Lumber Connectors HRC Hip Ridge Connectors For complementary top plate connection, see page 115 SUR/SUL/HSUR/HSUL Skewed 45 Hangers for I-Joist and SCL HSUR SUL2.56/11 MATERIAL: 16 gauge. FINISH: Galvanized INSTALLATION: Use all specified fasteners. See General Notes. On end of ridge-use optional diamond holes to secure the HRC. Bend face flanges back flush with ridge, and complete nailing. On face of ridge-adjust to correct height and install nails. Double bevel-cut hip members to achieve full bearing capacity. The HRC may be sloped to 45 with no reduction in loads. CODES: See page 12 for Code Listing Key Chart. Model No. Member Size Fasteners Doug Fir Larch/So. Pine Allowable Loads Spruce-Pine-Fir Allowable Loads W Ridge Carrying Member Each Hip Uplift (133) Uplift (160) Floor (100) Snow (115) Uplift (133) Uplift (160) Floor (100) Snow (115) HRC1.81 1 2x or 1 wide 16-10dx1 2-10dx1 240 290 720 830 210 250 625 720 Roof (125) 900 Roof Code Ref. (125) 780 160 1. Allowable loads shown are for each hip. Total load carried by the connector is double this number. 2. Uplift loads include a 33% and 60% increase for earthquake or wind loading; no further increase allowed; reduce where other loads govern. 3. Roof loads are 125% of floor loads unless limited by other criteria. 4. NAILS: 10dx1 0.148" dia. x 1 long. See page 16-17 for other nail sizes and information. HRC1.81 U.S. Patent 5,380,116 Typical HRCInstallation on the End of a Ridge Optional HRC1.81 Installation The SUR/L1.81, 2.56 and New HSUR/L4.12, 4.75 and 5.12 are improved 45 skewed hangers designed specifically to ease the installation of single and double I-Joists. In addition to Positive Angle Nailing these hangers encapsulate the top flange of the I-Joist, so no web stiffeners are required for standard installation. The full range of 45 skewed hangers feature obround nail holes on the acute side allowing nails to be easily installed parallel to the header and joist. Installation is further simplified with no required bevel cuts. MATERIAL: See table. FINISH: Galvanized. Some products available in Z-MAX; see Corrosion-Resistance, page 6-7. INSTALLATION: Use all specified fasteners. See General Notes. Illustrations show left and right skews SUR/L (SUR=skewed right; SUL=skewed left). The joist end may be square cut or bevel cut. Web stiffeners are required for I-Joist applications except for the SUR/L1.81, 2.56, HSUR/L4.12, 4.75 and 5.12. Fill all round and obround nail holes with specified fasteners to achieve table loads. Where noted,triangle holes in the joist flange may be filled for additional uplift capacity (see Footnote 3). OPTIONS: These hangers will accommodate a 40 to 50 skew. Available with the A2 flange turned in on 2-2x and 4x models only (see illustration). For example, specify HSURC410, HSULC410, SURC210-2, or SULC210-2. CODES: See page 12 for Code Listing Key Chart. This product is preferable to similar connectors because of a) easier installation, b) higher loads, c) lower installed cost, or a combination of these features.

[close]