Page 185 of Wood Construction Connectors 2006 Catalog by Simpson Strong-Tie

186 Architectural Products Group ARCHITECTURAL PRODUCTS GROUP ORNAMENTAL JOIST HANGER CONCEALED JOIST TIES 1.Center pin in beam. Short pin (2 for use with 3 GLB, 4x sawn lumber or 3 wide PSL. Long pin (4 for use with 5 GLB, 6x sawn lumber or greater widths. 2. See T-CJT for additional load information with long pins. The CJT is a concealed connector. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. MATERIAL: 12 gauge. FINISH: Galvanized INSTALLATION: Use all specified fasteners. See General Notes. The CJT Pack is supplied with all pins and screws required. Screws require a hex head driver. Router end of beam for screw heads for flush installation. The joist/beam may be sloped to 45 with full table loads. To provide maximum beam width for use with short pins, center in beam. Request F-CJT flier for installation instructions and ordering information. OPTIONS: See Technical Bulletin T-CJT. CODES: See page 12 for Code Listing Key Chart. Model No. Min. Joist Size Dimensions Fasteners Allowable Loads H1 H2 SDS Pins (2 or 4 2 Uplift (133) Floor (100) Snow (115) Roof (125) DOUGLAS-FIR CJT3 4x8 5 4 6 3 1050 1050 1050 CJT4 4x10 7 5 8 4 2440 2805 2815 CJT5 4x12 8 7 10 5 3005 3455 3755 CJT6 4x12 10 8 12 6 3535 3990 3990 GLULAM BEAM CJT3 3 x7 5 4 6 1240 1240 1240 CJT4 7 5 8 4 2440 2805 2900 CJT5 8 7 10 5 3005 3455 3755 CJT6 3 x9 3 x10 3 x12 3 x9 3 x9 3 x9 3 x11 10 8 12 6 3535 4065 4420 PSL CJT3 5 4 6 3 1655 1840 2115 2160 CJT4 7 5 8 4 2460 2145 2145 2145 CJT5 8 7 10 5 3255 3005 3455 3755 CJT6 10 8 12 6 4005 3535 4065 4420 Code Ref. 35, 126 35, 126 35, 126 3 1655 2460 3255 4005 1655 2460 3255 4005 Chamfered Steel Pin (Galvanized) Typical CJT Installation (Note that pins should be centered within beam) CJT5 (others similar) The OHU Ornamental Joist Hangers are heavy duty, load-rated joist hangers that are attached with Simpson x3 SDS yellow zinc finish wood screws (supplied with product). MATERIAL: 12 gauge FINISH: Textured powder-coated flat black paint. OPTIONS: No modifications. CODES: See page 12 for Code Listing Key Chart. 1. Allowable loads have been increased 33% and 60% for earthquake or wind loading with no further increase allowed; reduce where other loads govern. OHU Joist Size Model No. W H B No. of SDS x3 Wood Screws Douglas Fir Spruce Pine Fir Uplift (133) Uplift (160) Floor (100) Snow (115) Roof (125) Uplift (133) Uplift (160) Floor (100) Snow (115) Roof (125) Code Ref. Face Joist 4x6 OHU46-SDS3 3 5 4 6 4 1535 1535 1840 2120 2305 1290 1290 1585 1820 1980 4x8 OHU48-SDS3 3 6 4 8 6 1535 1535 2455 2675 2675 1290 1290 2110 2245 2245 4x10 OHU410-SDS3 3 8 4 12 6 2455 2525 3685 4235 4605 2110 2120 3170 3645 3960 4x12 OHU412-SDS3 3 10 4 12 8 2525 2525 3685 4235 4605 2120 2120 3170 3645 3960 4x14 OHU414-SDS3 3 12 4 14 10 2525 2525 4300 4945 5375 2120 2120 3695 4250 4620 170 6x6 OHU66-SDS3 5 5 4 6 4 1535 1535 1840 2120 2305 1290 1290 1585 1820 1980 6x8 OHU68-SDS3 5 7 4 12 6 2455 2525 3685 4235 4605 2110 2120 3170 3645 3960 6x10 OHU610-SDS3 5 9 4 14 6 2455 2525 4300 4945 5375 2110 2120 3695 4250 4620 6x12 OHU612-SDS3 5 11 4 16 8 2525 2525 4910 5630 5630 2120 2120 4225 4730 4730 6x14 OHU614-SDS3 5 13 4 18 10 3950 3950 5525 6355 6860 3320 3320 4750 5465 5765 Ga 12 12 12 12 12 12 12 12 12 12 Typical OHU Installation WARNING: Take special care installing this connector. The beam must be installed perpendicular to the support member. The connections components may be damaged if the beam is rotated from its opposite end during or after installation. Damaged components may not be noticeable and may reduce the connectors load carrying capacity. SDS x3 U.S. Patent 6,109,850

[close]