Page 28 of Wood Construction Connectors 2006 Catalog by Simpson Strong-Tie

Base Material Temp AT SET ET 0 F 24 hrs 25 F 8 hrs 40 F 4 hrs 72 hrs 72 hrs 60 F 1 hr 24 hrs 24 hrs 80 F 25 min 20 hrs 24 hrs 100 F 20 min 16 hrs 12 hrs WEDGE-ALL The Wedge-All is a non-bottom bearing, wedge style expansion anchor for use in solid concrete or grout filled masonry. A one-piece clip ensures uniform holding capacity that increases as tension is applied. The threaded stud version is available in nine diameters and multiple lengths. A single size tie-wire version is available for wire supported fixtures. Threaded studs are set by tightening the nut. Tie-wire anchors are set with the claw end of a hammer. CODES: ICC ER-1056 (Titen HD); ER-3631 (Wedge-All); City of L.A. RR24682; FL 2304.2 (Titen HD); FL 402.5 (Wedge-All). 29 Anchors ANCHOR SYSTEMS GENERAL INFORMATION ET EPOXY-TIE ADHESIVE Epoxy-Tie ET is a twocomponent, low odor, 1:1 ratio, 100% solids epoxybased system for use as a high strength, non-shrink anchor grouting material. ET offers an economical solution for general anchoring applications. Resin and hardener are dispensed and mixed simultaneously through the mixing nozzle. SET HIGH STRENGTH EPOXY Epoxy-Tie SET epoxy is a two-component, low odor, 1:1 ratio, 100% solids epoxy-based adhesive for use as a high strength, non-shrink anchor grouting material. SET is ideal for high load applications where strength is the main concern. Resin and hardener are dispensed and mixed simultaneously through the mixing nozzle. AT HIGH STRENGTH, ALL TEMPERATURE ADHESIVE Acrylic-Tie is a two-component, 10:1 ratio acrylic based adhesive for use as a high strength, anchor grouting material. Formulated for use in all types of weather, AT is designed to dispense easily and cure at temperatures down to 0 F. Resin and initiator are dispensed and mixed simultaneously through the mixing nozzle. TITEN HD The Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques. This heat-treated anchor undercuts the concrete to create a strong mechanical interlock over the entire length of the anchor. The anchor can be installed with a standard ANSI tolerance drill bit and is removeable. Recommended for permanent dry, interior, non-corrosive environments or temporary outdoor applications. Contact Simpson for more information. CODES: ICC ER-1722 (SET); ER-4945 (ET); ER-5791 (AT); City of L.A. RR 25279 (SET); RR 25185 and RR 25120 (ET); RR 25459 (AT); FL 402.3 (SET); FL 402.2 (ET); FL 2304.1 (AT). SET22 ET22 AT13 ADHESIVE ANCHOR SOLUTIONS MECHANICAL ANCHOR SOLUTIONS Refer to C-SAS-2006 for other Adhesive Solutions Refer to C-SAS-2006 for other Mechanical Anchor Solutions Available with additional corrosion protection. Check with factory. Wedge-All Titen HD U.S. Patent 5,674,035 6,623,228 Simpson Anchor Systems manufactures a full line of anchoring and fastening products for concrete and masonry. The product line includes adhesives for anchoring and crack injection, mechanical anchors, powder actuated fasteners and drill bits. Anchor Systems products offer unique solutions to applications in the light framed construction market when used with, and without, Simpson connectors. For complete information on product performance, installation requirements and appropriate code listings for Anchor Systems products please refer to the 2006 Anchor Systems catalog (form C-SAS-2006) or visit www.simpsonanchors.com. IN THE SPECS ON THE JOB AT YOUR SERVICE

[close]