Page 30 of Wood Construction Connectors 2006 Catalog by Simpson Strong-Tie

Anchors ANCHOR SYSTEMS Sill Plate Anchor Solutions 31 x 6 THD50600H 2 2x or 3x x 6 THD62612H 2 3x Titen HD Size (in.) Titen HD Model No. Sill Plate Size (in.) x 6 THD62600H 2 2x 8 10 Minimum End Distance 10 x 8 THD50800H 2 Double 2x 8 1 1 Minimum Edge Distance 1 1 Titen HD: As a Direct 1 to 1 Replacement for Sill Bolts 1. Minimum concrete strength 2500 psi. 2. For ACQ or CA pressure-treated wood order products Mechanically Galvanized (MG). For additional information, visit www.strongtie.com/info. 3. Designs based on a minimum emdedment of 3 for Titen HDs and 3 for Titen HDs. 4. For additional information, refer to the latest Simpson Anchor and Fastening Systems for Concrete Masonry catalog and T-ANCHORSUB. 5. Direct 1 to 1 replacement is based on parallel-to-plate, perpendicular-to-plate, and tension comparisons to a cast-inplace anchor bolt of equivalent diameter. 6. For concrete foundation only, 6" minimum stem wall width. 7. Minimum edge and end distances are based on distance from edge of concrete to center of bolt. RFB #4x7 4 2x 1 RFB #5x8 5 2x 1 RFB Size Minimum Embed. Sill Plate Size (in.) Minimum Edge Distance RFB #4x10 Double 2x or 3x 8 10 RFB #5x10 Double 2x or 3x Minimum End Distance RFB and SET/AT/ET: As a Direct 1 to 1 Replacement for Sill Bolts 1. Minimum concrete strength 2500 psi. 2. For ACQ or CA pressure-treated wood, order products HDG. For additional information, visit www.strongtie.com/info. 3. Direct 1 to 1 replacement is based on parallel-to-plate, perpendicular-to-plate, and tension comparisons to a cast-in-place anchor bolt of equivalent diameter. 4. For concrete foundations only. 5. Minimum edge and end distances are based on distance from edge of concrete to center of bolt. EXTERIOR/INTERIOR WALL ANCHORAGE SOLUTIONS INTERIOR (ONLY) WALL ANCHORAGE SOLUTIONS Simpson Anchor Systems offers a full line of powder actuated tools, fasteners and powder loads for fastening to concrete and steel. Powder actuated pins are often used to fasten the sill plate to concrete slabs. For complete information on product performance, installation requirements and appropriate code listings for Anchor Systems products please refer to the 2006 Anchor Systems catalog (form C-SAS-2006) or visit www.simpsonanchors.com. PHN PHNW 3 (76) (7.9) 12 (305) Maximum Spacing inches (mm) Catalog Number Overall Length inches (mm) Head Diameter inches (mm) PDPW-300 or PDPWL-300 PHN-72 or PHNW-72 2 (73) 0.145 (3.7) Shank Diameter inches (mm) 0.145 (3.7) (7.9) 18 (457) 24 (610) 36 (914) Interior Braced Walls 3 Interior Walls 2 1. Spacings are based upon the attachment of 2-inch (nominal thickness) wood sill plates, with specific gravity of 0.50 or greater, to concrete floor slabs or footings. For species of wood with specific gravity of 0.42 to 0.49, multiply required spacing of fasteners for shear walls by 0.81. For species of wood with specific gravity of 0.31 to 0.41, multiply the required spacing of fasteners for shear walls by 0.65. 2. All walls shall have fasteners placed at 6 inches from ends of sill plates, with maximum spacing as shown in the table. 3. Fasteners indicated shall have two pins placed 6 inches and 10 inches, respectively, from each end of sill plates, with maximum spacing as shown in the table. 4. All fasteners must be installed with a minimum 3/4-inch-diameter, No. 16 gauge (0.0598 inch) steel washer. 5. Fasteners shall not be driven until the concrete has reached a compressive strength of 2,000 psi. Minimum edge distance is 1 inches. 6. The fasteners shall not be used for the attachment of shear walls having a unit shear in excess of 100 pounds per foot. Spacings shown are independent of the number of building stories. PDPW PDPWL Available with additional corrosion protection. Check with factory. RFB Titen HD Simpson Anchor Systems offers several post-installed solutions for sill plate anchorage to concrete or concrete block foundations. Often times these products are used in retrofit applications or when cast-in-place anchors are omitted or mislocated. Some products are available in galvanized and stainless steel versions to address most pressure-treated wood applications. The following information provides some guidance when substituting Anchor Systems products for cast-in-place sill bolts. For complete information on product performance, installation requirements and appropriate code listings for Anchor Systems products please refer to the 2006 Anchor Systems catalog (form C-SAS-2006) or visit www.simpsonanchors.com.

[close]