Catalog: Wood Construction Connectors 2006 Catalog | |
| shank design, and point configuration to ensure conformity to published values. ... pneumatic nail use, see Instructions to the Installer, page 14 and visit www. ... ; SS10D 10d common; SS16D 16d common TO ORDER: Display Packages available for ... , N10DHDG, 10DHDG and 16DHDG nails. To order, specify: Nail Type Description ... and LSSU. 3.This table does not apply to specials (see Hanger Options), or steel ... with alternate nails. Use this table to determine the load adjustment factor. ... . 6.Recommended minimum end distance to prevent splitting is 10 x the nail ... Steel thickness varies according to mill standards. Use these Roof Pitch to ... Hip/Valley Rafter Roof Pitch conversion tables only for ... hip/valley rafters that are skewed 45 right or left. All ... other skews will cause the slope to change from that listed. If Common ... | |
| 82 This product is preferable to similar connectors because of a) easier ... U Hangers This series attach joists or rafters to headers, sloped up or down, and ... skewed left or right, up to 45 . MATERIAL: See table. FINISH: ... Listing Key Chart. STEP 1 Nail hanger to slope-cut carried member, installing ... skewed installation. STEP 2 Skew flange to form acute angle. Bend other flange ... one time only. STEP 3 Attach hanger to the carrying member, acute angle side ... may limit allowable loads. Refer to Technical Bulletins T-ANSITPISPF, T- ... | |
| HCP Installation The HCP connects a rafter or joist to double top plates at a 45 ... . See General Notes. Attach HCP to double top plates; birdsmouth not ... required for table loads. Install rafter and complete nailing. Rafter may be ... sloped to 45 . CODES: See page 12 for Code ... 1 Spruce-Pine-Fir Allowable Loads 1 To Rafters To Plates (133 160) (133 160) Uplift F1 ... with factory. The VPA is adjustable to slopes between 3:12 and 12:12, ... reduces the need for beveled plates and toe-nailing. MATERIAL: 18 gauge FINISH: Galvanized ... hole. Hammer nail in at a slight angle to prevent splitting. STEP 1 Install top ... nails and face PAN nails in A flange to outside wall top plate. STEP 2 Seat ... rafter with a hammer, adjusting B flange to ... | |
| This product is preferable to similar connectors because of a) easier ... The LSU5.12 must be factoryskewed 0 to 45 . It may be fieldsloped to 45 . ( ... SEQUENCE STEP 1 Nail hanger to slope-cut carried member, installing ... skewed installation. STEP 2 Skew flange to form acute angle. Bend other flange ... one time only. STEP 3 Attach hanger to the carrying member, acute angle side ... an angle. This series attach joists or rafters to headers, sloped up or down, and ... skewed left or right, up to 45 . MATERIAL: See table FINISH: ... | |
| , see page 116 The VPA is adjustable to slopes between 3:12 and 12:12, ... reduces the need for beveled plates and toe-nailing. MATERIAL: 18 gauge FINISH: Galvanized ... U.S. Patent 5,335,469 A and B flanges touch at 45 The HCP connects a rafter or ... joist to double top plates at a 45 angle. MATERIAL: 18 ... . See General Notes. Attach HCP to double top plates; birdsmouth not ... required for table loads. Install rafter and complete nailing. Rafter may be ... sloped to 45 . CODES: See page 12 for Code ... 1 Spruce-Pine-Fir Allowable Loads 1 To Rafters To Plates (133 160) (133 160) Uplift ... nail in at an approximate 45 angle to limit splitting. STEP 1 Install top ... nails and face PAN nails in A flange to outside wall top plate. STEP 2 Seat ... | |
| load from the truss or girder to plates for bearing-limited conditions, ... TBE4 used on 2x4 and TBE6 used on 2x6 top plates. The table gives the different ... . TBE must be installed in pairs. Top plate size is 2x4 for TBE4, 2x6 for ... Listing Key Chart. No. of Truss Plys Top Plate or Truss Wood Species 7 TBE Only ... 1, 4 TBE Wood Bearing Allowable Loads Total Bearing Length (TBL) 1, 4, 8 (100) ( ... 133/160) TBL (in) (133 160) Parallel to Plate 6 Perp to Plate 5 TBE4 ON 2x4 TOP ... 4.36 10605 4.36 10605 4.36 TBE6 ON 2x6 TOP PLATE 1 Doug-Fir-Larch 1820 2095 2275 ... attached wood members must be designed to withstand the loads imposed by the ... nails. 5. Perpendicular to Plate loads are reduced for Alternate ... Installation. 6. Parallel to Plate loads are not reduced for ... Alternate Installation. 7. Use lower of top plate or truss wood species. 8. Total ... | |
| General Notes. The HTC has a 2 slot to accommodate truss movement The S/HTC ... for short-term loading. 2. Truss or rafter must be bearing on top plate to achieve ... installed with maximum 1 space between rafter or truss and top plate use loads under ... are not required, space is not limited to 1 ". 4. NAILS: 10d 0.148" dia. x 3" ... Fasteners Allowable Loads 1 (133 160) Top Plate Base Slot Without Gap 2 With 1 ... flush against the connector, to allow vertical truss movement. Allow ... gap between nailhead and truss clip to help prevent squeaking HTC4 Typical ... completely flush against the connector, to allow vertical truss movement. Model ... illustration). Use STCT where truss or rafter is separated from the top plate of the ... for short-term loading. 2. Truss or rafter must be bearing on top plate to achieve ... | |
| 1,2 Spruce-Pine-Fir Allowable Loads 1,2 To Rafters/ Truss To CMU Uplift 4 Lateral ... 3 2-10dx1 18 H16-2S 6x2 Titen To Concrete 3 18 3 11 Code Ref 125 ... Presloped at 5:12. Pitch of 3:12 to 7:12 is acceptable H16 (H16-2 similar ... ) 3 HM9 Attaching Truss to Masonry 1 H16S Installed into Masonry ... loads are for one anchor. A minimum rafter thickness of 2 must be used when ... into Masonry The HM9 is designed to retrofit roof truss/rafters for block ... provides for various truss heightup to a maximum of 13 ". Minimum heel height ... do not replace solid blocking. Attach to grouted concrete block with a minimum ... one #5 rebar horizontal in the top lintel block. CODES: See page 12 for ... | |
| H2.5Ts truncated design was developed to accommodate trusses with 2x4 bottom ... chords. The easy to install, five nail pattern is stronger ... tie. It can be installed with rafter nailing flanges facing inwards or ... installation, with higher uplift loads to meet new code requirements. H5A has ... benefit, it only requires 6 nails, to meet lower uplift requirements. H2 H2.5 ... | |
| H2.5 Installation (Nails into both top plates) H3 Installation (Nails into ... upper top plate) H4 Installation (Nails into ... upper top plate) H5 Installation (Nails into both ... top plates) H6 Stud to Top Plate Installation 9 8 7 1 10 H5A ... Installation (Nails into both top plates) 11 12 2 3 H2.5A Installation ( ... Nails into both top plates) 4 H2.5T Installation (Nails ... into both top plates) 5 H6 Stud to Band Joist Installation 13 1. Loads ... loads are for one anchor. A minimum rafter thickness of 2 must be used when ... .5A). 3. Allowable uplift load for stud to bottom plate installation is 400 lbs ( ... in the F 1 direction are not intended to replace diaphragm boundary members or ... cross grain bending of the truss or rafter members. Additional shear transfer ... | |
| (H11Z similar) 19 20 H14 Installation to double top plates 21 16 18 Hurricane ... Tie Installations to Achieve Twice the Load (Top View) ... single ply 2x truss may cause the wood to split. H9 attaching truss to top ... 14 H7Z Installation H8 attaching stud to sill (4-8d into plate, 5-8d into stud ... ) H8 attaching I-joist to double top plates H9, H10 and H10R optional ... angle nailing connects shear blocking to rafter. Use 8d common nails. Slot ... allows maximum field-bending up to a pitch of 6/12, use 75% of the table ... uplift load? 2. What is the parallel-to-plate load? 3. What is the perpendicular-to- ... is the species of wood used for the rafter and the top plates? (Select the load ... the hurricane tie be nailed into both top plates or the upper top plate only? 6 ... | |
| Loads 1 SPF/HF Allowable Loads 1 To Rafters/Truss To Plates To Studs Uplift Lateral ... wind and seismic ties for trusses and rafters. The presloped seat of the H16 provides ... provides for various truss height up to a maximum of 13 " (H16 series). Minimum ... H16 series is 4". The HGA10 attaches to gable trusses and provides good lateral ... attaches the bottom chord of a truss or rafter at pitches from 0:12 to 4:12 to double ... 2x4 top plates. Double shear nailing allows for ... only when bottom chord of truss or rafter has no slope. Hurricane Ties do not ... be avoided, mechanical reinforcement to resist such forces should be considered ... H16S Presloped at 5:12. Pitch of 3:12 to 7:12 is acceptable H15 Installation ... HGA10 Installation to Double Top Plates Pitch 0:12 to 7:12 F1 F2 HS24 ... | |
| of the fasteners on each end of strap to achieve full loads. 3.Loads have been ... MTS Installation as a Truss-to- Top Plate Tie 1" TYP . L 1 " MTS30C ( ... the strap. 5.Twist straps do not have to be wrapped over the truss to achieve ... 88, 121 1. F1 Loads may be increased up to 25% for short-term loading in ... MTS30 Installation with I-joist Rafter Available with additional corrosion ... | |
| loads are for one anchor attached to blocking minimum 1 thick. 2.RBC can be ... installed with up to gap and achieve 100% of the listed load ... other loads govern. 4.When attaching to concrete use 3- x1 Titens. 5.RBC ... of 395 lb. (133/160%) in a parallel to wall (F 1) load direction for Douglas ... -Fir-Larch/ So. Pine Allowable Loads To Plate To Blocking Lateral (133/160) ... Loads Lateral (133/160) 1 45 to 90 440 6-10dx1 6-10dx1 6-10dx1 6- ... 10dx1 3- "x2 Titen 6-10dx1 380 2 0 to 30 485 420 160 3 0 to 45 350 350 ... Fasteners 4 Typical RBC Installation to CMU Block 3 2 Typical RBC Installation ... The RBC Roof Boundary Clip is designed to aid installation and transfer shear ... between the roof diaphragm and wall top plates. The locator tabs make proper ... and will handle roof pitches from 0:12 to 12:12. MATERIAL: 20 gauge FINISH: ... | |
| a 90 angle. RCBZ can be used anywhere to strengthen a 90 angle and can be used ... pressure treated wood, fasteners need to be minimum of HDG. CODES: See page 12 ... members. 16 gauge steel conforms to the National Electric Code. MATERIAL: ... Key Chart. PSPN516Z (16 gauge ZMAX at top plates International Residential Code ... /2003 305.8 PSPN58Z (16 gauge ZMAX at top plates and bottom plate. International ... Code 2000/2003 P2603.2.1 NS1 nail stops to protect supply lines from drywall ... 1.25" from the edge of a joist, stud or rafter or shall be protected with a 16 gauge ... Ref. 190 PSPN58Z PSPN516Z Installation to Sill Plate PSPN516Z Installed to Double ... Top Plates Typical NS Installation ... lbs (160) for SPF/HF. 16-16d nails in to top plates achieves 1515 lbs (133), ... | |
| 2 minimum lumber thickness is required to achieve the full load. 3. NAILS: 16d 0. ... and correct nailing locations. For a rafter-to-face connector, flatten the top flange into ... plane. The RR may be used with any rafter sloped up to 30 . MATERIAL: 18 gauge ... Code Listing Key Chart. Model No. Min. Rafter Size Fasteners Uplift (133/ 160) ... Allowable Loads 1 Header Rafter DF/SP Floor (100) Roof (125) RR 2x6 4- ... for other load durations according to the code, provided they do not exceed ... Brackets FC Framing Clips RR Ridge Rafter Connector PSCL Panel Sheathing Clips 1 ... | |
| TYPICAL ROOF CONNECTIONS Pages 162 to 168 TYPICAL FLOOR-TO-FLOOR CONNECTIONS ... Pages 35 to 45, 155 to 160 TYPICAL FOUNDATION CONNECTIONS ... Pages 23 to 34 This drawing shows the connection ... continuous load transfer path from the rafters to the foundation of a two-story ... of creating a structure better able to withstand the forces of mother nature ... considered an engineered system. Refer to the page numbers for the full range ... . Consult a qualified Designer to ensure that correct connector ... and installation methods are used to achieve the full design load values. ... Tiedown Systems This System is designed to provide the over-turning holdown ... . This holdown application is easy to specify, install and inspect. High Wind ... and tested using screw fasteners to obtain actual load values. Includes ... | |
