Catalog: Wood Construction Connectors 2006 Catalog | |
| 6 Wood Construction Connectors TABLE OF CONTENTS CORROSION INFORMATION ... 18, 19 CONCRETE CONNECTORS Anchor Adhesives ... 62-67 SOLID SAWN CONNECTORS Adjustable Hangers ... Mount Hangers ........ 76 Sloped/Skewed Connectors ................ 82, 86 Top Flange ... WOOD STRUCTURAL COMPOSITE LUMBER CONNECTORS Adjustable Hangers ... 118 Sloped/Skewed Connectors ............ 114, 117 Top Flange ... 97-113 GLULAM BEAM CONNECTORS Concealed Joist Tie ... ....................... 119, 120 Hinge Connectors............... ..................... 161 Top Flange ... 121-123 PLATED TRUSS CONNECTORS Adjustable Hangers ... 137, 138 MASONRY CONNECTORS Brick Ties ... 182 Hurricane Connectors ...................... 149-154 Straps ... 183 Deck Connectors ......................... ............ ... 166 Hip Connectors ......................... ........ 83, ... | |
| 7 Wood Construction Connectors CORROSION INFORMATION SIMPSON COATINGS ... AVAILABLE Contact Simpson for product availability, ordering ... steel products, and are available from Simpson. TM STANDARD COATING G90 (Galvanized G90 ... zinc per square foot of surface area. Simpson Strong-Tie began producing connectors ... to steel. If you choose to use ZMAX or HDG on an outdoor project (i.e. deck ... you should periodically inspect your connectors and fasteners or have a professional ... CA-B (Ground Contact), Stainless Steel connectors and fasteners are recommended. Verify ... treater. When using Stainless Steel connectors, use Stainless Steel fasteners. When ... using ZMAX/HDG galvanized connectors, use fasteners galvanized per ASTM A153 ... . Due to the many variables involved, Simpson cannot provide estimates on service ... | |
| 985 1135 3465 13 Wood Construction Connectors HOW TO USE THIS CATALOG STEEL STRESS ... the way allowable loads on some connectors are determined when using Allowable ... events. Specifically, the codes allowed Simpson Strong-Tie to take a one-third stress ... calculated tensile capacity of steel connectors. Newer codes and standards only allow ... so stress increases are not permitted. Simpson Strong-Tie determines allowable loads ... practice. Because of these changes, Simpson Strong-Tie re-evaluated its entire ... increase on the steel. The majority of Simpson Strong-Ties products were not affected ... load is applied. Model No.: This is the Simpson product name. Uplift Down Lateral ... with additional corrosion protection (ZMAX, Hot-Dip Galvanized or Stainless Steel ... corrosion protection is provided (Z ZMAX, HDG Hot-Dip Galvanized or SS Stainless ... | |
| . This finish is not acceptable for ZMAX or HDG applications. 2.HDG hot-dip ... sinker nails are for reference only. Simpson does not sell these nails. All other ... nails are available through Simpson. 5.For pneumatic fastener info, request ... Table C12.4.1. 7.Use HDG nails with ZMAX and HDG products. 8.16d sinker with GV ... finish is not acceptable for ZMAX or HDG applications. Display Package ... | |
| SDS Screws. Fits a standard drill. The Simpson Strong-Drive wood screw has a hex ... with their corresponding HDG or ZMAX connectors. 11. SDS-HDG available in bulk or 50- ... SD8x1.25" wood screws with structural connectors Spacing (in) Edge Dist. (in) ... | |
| 23 Concrete Connectors BP/LBP Bearing Plates Typical WT ... be ordered HDG, LBPs may be ordered ZMAX check factory. Refer to page 6-7 for ... | |
| Strap Tie Holdowns Wood-to-concrete connectors that satisfy engineering and code ... : Galvanized, some models available in ZMAX or HDG. INSTALLATION: Use all specified ... | |
| . H2.5A* MIN. H2.5A MIN. H2.5A* MIN. *ZMAX connectors (for example, H2.5AZ) should ... | |
| 83 Solid Sawn Connectors VPA Adjustable Variable Pitch ... Connectors HCP Hip Corner Plates Typical HCP ... FINISH: HCP2-galvanized or Z-MAX; HCP4Z-ZMAX . INSTALLATION: Use all specified ... | |
| Galvanized, some products available in ZMAX. See Corrosion-Resistance, page 6-7. ... top plate, and RPS28Z (16 gauge ZMAX to reinforce sill plate. International ... | |
| : 16 gauge FINISH: Galvanized, PSPN-ZMAX. INSTALLATION: PSPN 16d commons. Other ... Listing Key Chart. PSPN516Z (16 gauge ZMAX at top plates International ... Code 2000/2003 305.8 PSPN516Z (16 gauge ZMAX at bottom plate. International Building ... Code 2000/2003 305.8 PSPN58Z (16 gauge ZMAX at top plates and bottom plate. ... with factory. RCBZ Rigid Corner Bracket ZMAX 1. PSPN516Z: 12-16d nails into sill ... | |
