Catalog: Wood Construction Connectors 2006 Catalog | |
| Bolts RFBs are clean, oil free, pre-cut threaded rod, supplied with nut and washer. ... anchoring system when used with the Epoxy-Tie or SET Epoxy. Inspection is ... easy; the head is stamped with rod length and No ... for application information and request T-ANCHORSPEC for additional product use information ... Model No. Rod Diameter H Min Allowable Tension Capacity (lbs.) (100) CNW 0.625 1 CNW ... 0.750 2 2 HSCNW1 1.000 18225 32400 Transition Couplers CNW 0.625 to 0.500 1 3750 ... CNW 0.750 to 0.625 1 CNW 0.875 to 0.625 2 5875 5875 CNW1- 1.000 to 0.875 ... fast visual check for correct all thread rod installation HSCNW High Strength ... | |
| 1. Loads may not be increased for short-term loading. 2. A mudsill on top of the GH ... is required to achieve the table loads. 3. Models listed are for a 2x ... for other nail sizes and information. Typical GH Installation GH A girder-to- ... into girder. H girder height mudsill thickness. 1 clearance hole accommodates rebar or ... anchor. This is not required. OPTIONS: For skewed ... Listing Key Chart. GH Girder Hangers The UFP10 Retrofit Foundation Plate cuts ... installation time in half. Designed to connect when the mudsill is offset from ... the foundation up to 2 or extended beyond the foundation up ... | |
| solutions for holdowns and bases. Often times these products are used when cast-in- ... , or in retrofit applications. The following design values provide ... solutions to common applications encountered in the ... a more complete solution guide refer to the Anchor Systems Specifications for ... Connectors catalog (T-ANCHORSPEC). For complete information on product ... Anchor Systems products please refer to the 2006 Anchor Systems catalog (form C ... changed from previous catalogs. Refer to the C-SAS-2006 or download our ... technical bulletin (T-STEM06) at www.strongtie.com for the latest ... | |
| For holdowns, per ASTM test standards, anchor bolt nut should be ... finger-tight plus to turn with a hand wrench, with consideration ... given to possible future wood shrinkage. Care ... should be taken to not over-torque the nut. Impact wrenches should not be used ... . NEW! The HDU series of holdowns are the latest in a long series of innovations ... from Simpson. These holdowns combine the advantages of low deflection and high ... capacity from the pre-deflected geometry with the ease of ... virtually eliminates deflection due to material stretch. Uses SDS screws ... provides a greater net section area of the post compared to bolts. SDS x2 screws ... | |
| No. Ga Dimensions Fasteners Allowable Tension Loads SPF/HF (133/160) Holdown 5 ... Load Raised .081 .077 .073 Allowable Tension Loads DF/SP (133/160) 3610 4685 5860 ... where other load durations govern. 2.The Designer must specify anchor bolt type ... , length and embedment. See the SSTB and SSTBL Anchor Bolts (page 33-34 ... bolt. 4.Loads are based on static tests on wood studs, limited by the lowest ... of 0.125" deflection, test ultimate divided by 3, or the wood ... at Highest Allowable Design Load: The deflection of a holdown measured ... between the anchor bolt and the strap portion of the holdown when ... loaded to the highest allowable load listed in the ... | |
| . No. of SDS x2 Wood Screws Allowable Tension Loads DF/SP (133/160) Holdown ... Deflection at Highest Allowable Tension Design Load Code Ref. HHDQ11-SDS2.5 7 ... 0.081 160 L 3 3 1 1 1 1 Allowable Tension Loads SPF/HF (133/160) 9615 12350 1. ... govern. 2. Loads are based on static tests on wood posts, limited by the lowest of ... 0.125" deflection, test ultimate divided by 3, or the SDS wood ... screw value. 3. HHDQs can be raised off the sill with no reduction in load or ... . HHDQ11 Vertical HHDQ11 Installation The heavy-duty HHDQ holdowns combine low ... supplied. (Lag screws will not achieve the same load.) The load transfer plate is ... an integral part of the HHDQ; no additional washer is required ... | |
| 38 Anchors HDA/HD Holdowns * Typical HD5A Tie between Floors Vertical HD15 ... bolt. Washers are not required at the base. HD10A (HD6A, HD8A and HD14A ... similar) * To achieve table loads, the minimum bolt end distance is seven bolt ... diameters. This distance is designed into holdowns. ... BPs are required by the City of Los Angeles. Check with your ... of a standard cut washer.) Pressure-treated barrier may be required. Holdowns are ... used to transfer tension loads between floors, to tie purlins ... to masonry or concrete, etc. Use HDAs and ... requirements and other applications to transfer tension loads. All HDAs and ... | |
| 40 Anchors LTT/MTT/HTT Tension Ties Model No. Material (Ga) Dimensions ... Fasteners Allowable Tension Loads SPF/HF Deflection at Highest ... 40, 97, 99, 122 40, 122 .125 Allowable Tension Loads DF/SP (133) (160) Nails Bolts N ... 5250 5260 4455 2150 4455 2725 Seat Thickness Code Ref. C L 1. Allowable loads for ... HTT are based on the lower of the 2001 NDS fastener values or the ... ultimate load on a steel test jig divided by 2.5. 2. 16d sinkers (0. ... or 10d commons may be substituted for the specified 16d commons at 0.85 of the ... table loads. 3. The Designer must specify anchor bolt type ... values are based on a minimum lumber thickness of 1 ". 6. If a or anchor bolt is used ... | |
| may not be increased for short-term loading. 3. Specifier to design ... with 8-SDS X3 wood screws for the same table load. 5. For higher ... on column or concrete, according to the code. 6. HB dimension is the distance ... from the bottom of the post up to the first bolt hole. 7. NAILS: 16d 0.162" ... 1. Loads may not be increased for short-term loading. ABE44 Typical ABE46R ... sizes similar) U.S. Patent 5,333,435 Typical AB Installation ABU88 The AB is an ... hardware appearance. Post Bases provide tested capacity. They feature 1" standoff ... when supporting permanent structures that are exposed to the weather or water ... | |
