65 results for wood to wood anchors found in 0.000 seconds

4 Wood Construction Connectors ALPHABETICAL ... indicates a product that is preferable to similar connectors because of a) ...

5 Wood Construction Connectors INTRODUCTION ... Drive 21-28 Concrete Connectors 29-45 Anchors 46-55 Caps Bases 56-67 Shearwall 68-87 ... Sawn Connectors 88-118 Engineered Wood Structural Composite Lumber Connectors ... in 1914 and has been manufacturing wood-to-wood and wood-to-concrete connectors since ... Strong-Tie Company, Inc., has grown to be the worlds largest manufacturer of ... construction connectors and to expand to include a complete line of anchor ... sales team. In-house R D, and tool and die professionals. In-house ... for product quality and is committed to ensuring the effectiveness of the ... Quality Management System. Tom Fitzmyers Chief Executive Officer Steve ... information at hand. This will help us to serve you promptly and efficiently. ...

6 Wood Construction Connectors TABLE OF ... 21 Foundation Anchors ......................... ... 26, 27 ... 35-45 Mudsill Anchors ......................... ......... 24 ... , 25 Purlin Anchors ... 41 Strap Anchors ... 40 Truss Anchors ......................... ........ 150 ... 23 ANCHORS Floor Tie Anchors ......................... ........... ... 160 Framing Anchors.................. ................... 169 Holdowns ... Connectors ................ 82, 86 Top Flange Hangers ... 77-81 ENGINEERED WOOD STRUCTURAL COMPOSITE LUMBER CONNECTORS ... 90-96 Purlin Anchors ... Skewed Connectors ............ 114, 117 Top Flange Hangers ... 161 Top Flange Hangers ... .................... 132-136 Multi-Ply Wood Trusses .................. 139, 140 Top ... 147-149 Truss Anchors ......................... ........ 150 ...

7 Wood Construction Connectors CORROSION ... weight is 2.0 oz./ft 2 (per ASTM A123 total both sides). These products require hot ... area (hot-dip galvanized per ASTM A653 total both sides). Z-MAX meets all catalog ... minimum for most of the world equates to G90. We began producing product in G90 ... markets, but in the late 90s we decided to produce all our structural products ... are generally more corrosive to steel. If you choose to use ZMAX or ... including water-proofing of the wood used in your outdoor project is also a ... good practice. For wood with actual retention levels greater ... Verify actual retention level with the wood treater. When using Stainless Steel ... per ASTM A153. Testing indicates wood installed dry reduces potential ... corrosion. If dry wood is used, see our website for additional ...

5 3 12-16d 1500 985 1135 3465 13 Wood Construction Connectors HOW TO USE THIS ... allowed designers and manufacturers to take a one-third stress increase on the ... , the codes allowed Simpson Strong-Tie to take a one-third stress increase on the ... re-evaluated its entire product line to determine which loads were governed by ... load is governed Load Combination Cd (Wood) Allowed 2000 International Building ... the fastener quantity and type required to achieve the table loads. Throughout ... for more technical information on this topic. SIMPSON SPEC This icon indicates a ... product that is preferable to similar connectors because of a) ... 12 for the Code Listing Key Chart, to determine which code reports include ... : a minimum of 3 static load tests in wood assemblies; a minimum of 3 static load ...

14 Wood Construction Connectors IMPORTANT ... Strong-Tie Co., Inc. reserves the right to change specifications, designs, and ... , bolts and nails may not be combined to achieve highest load value. 8d (0.131" ... be noted (for example 8dx1 ). Refer to page 16, 17, NDS (National Design ... conditions must be adjusted according to the code. In many cases, Simpson code ... , since the specific gravity of these wood species fall within the specific ... specific gravity for the different wood species as listed by NDS. For your ... ksi, respectively. h. All references to bolts or machine bolts (MBs) are for ... through bolts (not lag screws) equal to or better than ASTM Standard A307, ... replaced. j. A fastener that splits the wood will not take the design load. Evaluate ... splits to determine if the connection will ...

15 Wood Construction Connectors IMPORTANT ... a. The allowable load is limited to the lowest of deflection, lowest test ... Uplift Design Lateral Parallel to Plate/Allowable Lateral Parallel to ... Plate Design Lateral Perpendicular to Plate/Allowable Lateral Perpendicular ... to Plate 1.0. c. Loads are based on the ... of load adjustments for fasteners into wood as specified by the code are as ... loading. e. Unless otherwise noted, wood shear is not considered in the loads ... given; reduce allowable loads when wood shear is limiting. Glulam 145 psi, LVL ... recommends the following addition to construction drawings and ... connectors are specifically required to meet the structural calculations of ... approval for substitution prior to installation. g. Verify that the ...

has a deep socket and magnetic tip to help provide a positive installation ... drill. The Simpson Strong-Drive wood screw has a hex washer head for easy ... -in reamer and type 17 tip cuts a hole to allow installation without predrilling ... on the type and moisture content of wood. Use drill bit. WARNING: Industry ... for Code Listing Key Chart. Model No. Wood Screw Description (Metric Equivalent) ( ... /Southern Pine Allowable Loads 1 14 ga to 3 ga 13 14 ga to 3 ga 13 Shear (100) ... 395 395 395 170 Code 9 Ref. Shear 6 Wood to Wood (DF to DF) 240 240 260 260 ... 525 525 525 525 240 200 220 220 Shear 6 Wood to Wood (SPF to SPF) 1500 1300 1100 ( ... . New tested loads have been submitted to the Code Report Agencies. 10. The SDS ... based on NDS calculation for a #14 wood screw or tested ultimate/5. If thread ...

application information and request T-ANCHORSPEC for additional product use information ... 32400 Transition Couplers CNW 0.625 to 0.500 1 3750 CNW 0.750 to 0.625 1 ... CNW 0.875 to 0.625 2 5875 5875 CNW1- 1.000 to 0.875 ... CNWs and HSCNWs provide a positive stop to allow even bolt threading top and ...

ANCHORMATE Anchor Bolt Holders Designed to hold the anchor in place before the ... . Lightweight, durable and easy to use. Reusable yet cost-efficient for ... . Use the 5/8" and 7/8" AnchorMate to secure the SSTB to the formboard ... coded buckets of 100 parts with a flip-top lid for easy access or bags of 10 ... : Keeps the SSTB bolts from moving due to the force of the concrete pour. ... Supports the bolt approx. 8" below the top of the concrete. Model ABS is for the ... 180 Code Ref. The StrapMate is designed to keep the STHD, LSTHD, HPAHD and PAHD ... Engineered Composite Plastic. Designed to fit plywood forms up to 1 LVL forms ...

finish. The BP SKT uses SDS x 1 screws to provide lateral resistance when ... be ordered ZMAX check factory. Refer to page 6-7 for corrosion information. ... than 4' high. Wall thickness from 6" to 12". Request technical bulletin T-WT ...

Connectors LMA/MASB/MAS/MAB/MA Mudsill Anchors 1.Loads have been increased for short- ... loads, provide attachment from mudsill to buildings structural components to ... . 3.MAS installed with 1 leg attached to stud has loads of 435 lbs (uplift), ... 700 lbs (parallel to plate) and 240 lbs. (perpendicular to ... ). 4.MASB installed with 1 leg attached to stud has load of 960 lbs (parallel to ... plate) and 360 lbs (perpendicular to plate). 5.MA installed attached to the ... Simpson. 6.LMA installed attached to the stud has no load reduction for ... 1 (133) Allowable Loads 1 (160) Sides Total Top Uplift 2 Parallel to Plate (F1) ... Perp to Plate (F2) Parallel to Plate (F1) Perp to Plate (F2) Uplift 2 ... into concrete after pour. Finish up to the edge of slab. No anchor bolts to ...

Connectors LMA/MASB/MAS/MAB/MA Mudsill Anchors MASB Model No. O.C. Spacing to replace ... " Anchor Bolt 6' O.C. O.C. Spacing to replace " Anchor Bolt 6' O.C. (133) ( ... MAS Installation 3 " 2x4 PLATE 1. Place anchors not more than 1' from the end of each ... code. 2. Spacing is based on parallel to plate load direction only. 3. All grout ...

for short-term loading. 2. A mudsill on top of the GH is required to achieve the ... . Typical GH Installation GH A girder-to-foundation wall connection. MATERIAL: 12 gauge. ... installation time in half. Designed to connect when the mudsill is offset from ... the foundation up to 2 or extended beyond the foundation up ... to ". The UFP may be used in place of the ... not achieve published loads. Refer to T-ANCHORSPEC for post-installed ... Key Chart. Model No. Max Spacing to replace Anchor Bolt or dia. Fasteners ... Allowable Load Parallel to Plate (133) Code Ref. Anchor Bolt Plate ...

FA/FAP/HFA/FJA/FSA Foundation Anchors This series is for retrofit or new ... . These products may be used together as a system or in individual ... wind conditions. FA and HFA Foundation Anchors eliminate vertical drilling by nailing ... into the top of the mudsill. They facilitate ... . The FAP Plate connects the mudsill to the foundation. Designed to provide ... Foundation Stud Anchor nails or bolts to floor joist, or nails to stud. Plywood ... may require notching with stud-to-foundation installation. MATERIAL: FAP 7 gauge; ... Key Chart. Model No. Max Spacing to Replace Anchor Bolts Fasteners ... For redwood mudsills, reduce F1 on HFA to 1215 lbs, and 840 lbs on FAP. 3. ... Spacing to be specified by the Designer. 4. FAP ... shall use a minimum SDS wood screw length of 2 plus the shim ...

are set by tightening the nut. Tie-wire anchors are set with the claw end of a hammer. ... .2 (Titen HD); FL 402.5 (Wedge-All). 29 Anchors ANCHOR SYSTEMS GENERAL INFORMATION ET ... in all types of weather, AT is designed to dispense easily and cure at ... temperatures down to 0 F. Resin and initiator are dispensed ... cutting teeth enable the Titen HD to be installed in one eighth of the time ... when compared to traditional expansion anchors, and at significantly reduced ... installation torques. This heat-treated anchor undercuts the ... concrete to create a strong mechanical interlock ... can be installed with a standard ANSI tolerance drill bit and is removeable. ... MECHANICAL ANCHOR SOLUTIONS Refer to C-SAS-2006 for other Adhesive Solutions ... Refer to C-SAS-2006 for other Mechanical Anchor ...

30 Anchors ANCHOR SYSTEMS Holdown and Post Base ... products are used when cast-in-place anchors are omitted or mislocated, or in ... design values provide solutions to common applications encountered in the ... a more complete solution guide refer to the Anchor Systems Specifications for ... Connectors catalog (T-ANCHORSPEC). For complete information on product ... Anchor Systems products please refer to the 2006 Anchor Systems catalog (form C ... changed from previous catalogs. Refer to the C-SAS-2006 or download our ... and Shear Loads for Threaded Rod Anchors in Concrete Allow. lbs. Allow. lbs. ... 33 percent for short-term loading due to wind or seismic forces with no further ... increase allowed. 5. Anchors are not permitted for use in ... construction. Exceptions are: (1) Anchors designed to resist wind or seismic ...

Anchors ANCHOR SYSTEMS Sill Plate Anchor ... Distance 1 1 Titen HD: As a Direct 1 to 1 Replacement for Sill Bolts 1. Minimum ... psi. 2. For ACQ or CA pressure-treated wood order products Mechanically Galvanized ... . 4. For additional information, refer to the latest Simpson Anchor and ... for Concrete Masonry catalog and T-ANCHORSUB. 5. Direct 1 to 1 replacement is based ... on parallel-to-plate, perpendicular-to-plate, and tension comparisons to a cast- ... on distance from edge of concrete to center of bolt. RFB #4x7 4 2x 1 RFB # ... RFB and SET/AT/ET: As a Direct 1 to 1 Replacement for Sill Bolts 1. Minimum ... psi. 2. For ACQ or CA pressure-treated wood, order products HDG. For additional ... www.strongtie.com/info. 3. Direct 1 to 1 replacement is based on parallel-to- ...

32 Anchors ANCHOR SYSTEMS Ledger and Purlin ... in this catalog is an introduction to Anchoring and Fastening Systems for ... Manual/Binder, call Simpson and ask to speak with your local Technical Sales ... the C-SAS-2006 catalog in easy-to-use tabular format, as well as code reports ... www.simpsonanchors.com/as k for answers to your questions or check our Frequently ... and fastening needs. In addition to complete product information and the ... and mechanical anchor solutions to anchor ledgers to concrete and concrete ... hollow). These products are also used to anchor roof connections in new and ... Anchor Systems products please refer to the 2006 Anchor Systems catalog (form C ... for a Ledger Shear Bolt 1. Titen HD anchors installed with the dimensional ... described shall achieve equivalent NDS wood calculated capacity as the same ...

. Extensive SSTB testing has been done to determine the design load capacity at ... on page 34. Install one #4 rebar 3" to 5" (may be foundation rebar not post- ... tension cable) from the top of the foundation. The SSTB does not ... need to be tied to the rebar. Minimum concrete compression ... beneath, unless provisions are made to transfer the load, or the slab is ... designed to resist the load imposed by the anchor ... ) approximately one rebar 12" from the top and two rebars approximately 28" from ... the top. Vertical #4 rebar (minimum 24" long) ... for short-term loading. Loads apply to earthquake and wind loading. 2. Minimum ... anchor center-to-center spacing is 2le for anchors acting in ... . 12. Minimum end distance required to achieve table loads is le. SELECTION ... depth unless provisions are made to transfer the load. 3.The design ...

34 Anchors SSTB Anchor Bolts Two Pour Installation ... Installation (Install with arrow on top of the bolt oriented as shown) Corner ... Installation (Install with arrow on top of the bolt oriented as shown) Non- ... (Bolt may be installed 45 to 135 as shown) Outer Edge of Concrete ... noted otherwise. 3. Spacing between anchors is 2l e minimum for anchors in tension ...

bolt nut should be finger-tight plus to turn with a hand wrench, with ... consideration given to possible future wood shrinkage. Care should be taken to not ... over-torque the nut. Impact wrenches should not be ... virtually eliminates deflection due to material stretch. Uses SDS screws ... net section area of the post compared to bolts. SDS x2 screws are supplied with ... for the installer. No stud bolts to countersink at openings. MATERIAL: See ... bolt. No additional washer required. To tie double 2x members together, the ... must determine the fasteners required to bind the members to act as one unit ... without splitting the wood. See SSTB Anchor Bolts on page 33-34 ... for tested, load-rated retrofit anchors or request T-ANCHORSPEC for more ... . 2. Loads are based on static tests on wood posts, limited by the lowest of 0.125" ...

36 Anchors PHD Predeflected Holdown HDQ8 Holdown ... W H B Anchor Dia. No. of Simpson SDS x3 Wood Screws PHD2-SDS3 14 3 9 2 1 10 ... . 4.Loads are based on static tests on wood studs, limited by the lowest of 0.125 ... , test ultimate divided by 3, or the wood screw value. 5.Deflection at Highest ... portion of the holdown when loaded to the highest allowable load listed in ... table. This movement is strictly due to the holdown deformation under a static ... load test conducted on a wood jig. 6. SDS screws install best with a ... PHD Installation (shown flush , touching sill plate) SDS x3 Screw US Patent No ... lumber columns, screws must be applied to the wide face of the column. 9. ... are installed on both sides of the wood member provided either the post is ... large enough or the holdowns are offset to eliminate screw interferences. 10. ...

37 Anchors HHDQ Heavy Duty Holdowns HDC Concentric ... No. H B C Anchor Dia. No. of SDS x2 Wood Screws Allowable Tension Loads DF/SP ( ... . 2. Loads are based on static tests on wood posts, limited by the lowest of 0.125 ... test ultimate divided by 3, or the SDS wood screw value. 3. HHDQs can be raised off ... applications. Install Simpson SDS1/4x2 wood screws, which are supplied. (Lag ... lumber columns, screws must be applied to the wide face of the column. 7. Post ... . 3. Loads are based on static tests on wood studs, limited by the lowest of 0.125" ... , test ultimate divided by 3, or the wood screw value. 4. Deflection at Highest ... portion of the holdown when loaded to the highest allowable load listed in ... table. This movement is strictly due to the holdown deformation under a static ... load test conducted on a wood jig. 5. SDS screws install best with a ...

38 Anchors HDA/HD Holdowns * Typical HD5A Tie ... HD10A (HD6A, HD8A and HD14A similar) * To achieve table loads, the minimum bolt ... may be required. Holdowns are used to transfer tension loads between floors, ... to tie purlins to masonry or concrete, etc. Use HDAs and ... requirements and other applications to transfer tension loads. All HDAs and ... diameter spacing from the end of the wood member to the center of the first bolt ... See General Notes. Contact engineered wood manufacturers for connections that are ... bolt. Bolt holes shall be a minimum of to a maximum of larger than the bolt ... ), and on stud bolt nuts against the wood. The Load Transfer Plate is an integral ... any alternate anchorage calculated to resist the tension load for a specific ... job. Locate on wood member to maintain a minimum distance of seven ...

39 Anchors HDA/HD Holdowns Model No. Material ... HD6A HD8A HD10A HD14A HD15 Code Ref. Wood Member Thickness 1 2 2 3 3 5 1320 ... at Highest Allowable Design Load Raised Wood Member Thickness 1 2 2 3 3 5 1555 ... portion of the holdown when loaded to the highest allowable load listed in ... table. This movement is strictly due to the holdown deformation under a static ... lumber columns, bolts must be applied to the wide face of the column. 11. The ... wide shearwall) or a 6x6 nominal post to ensure the tension load carrying ... HD14A. Minimum post size is required to ensure the tension load carrying ... distance from the end of the stud to the center of the first stud bolt hole ... See notes below. A B and F do not apply to the PHD and HDQ. A. Bolt slip can occur ... under load caused by stresses due to earthquake or high wind. G. Lateral ...

40 Anchors LTT/MTT/HTT Tension Ties Model No. ... the LTT20B, add a standard cut washer to the seat. No additional washer is ... with the body of the holdown to achieve table loads. See Girder ... spacing makes the LTT20B suitable for wood I-joists if 10dx1 nails are substituted ... 16ds. The LTTI31 is designed for wood chord open web truss attachments to ... the specified number and type of nails to attach the strap portion to the top or ... or 4x4), except LTT19). Bolt the base to the wall or foundation with a suitable ... rated epoxies for anchor bolt options. To tie double 2x members together, the ... must determine the fasteners required to bind members to act as one unit ... without splitting the wood. See Simpson Anchor Systems for tested ... , load-rated anchors and request T-ANCHORSPEC for more information. CODES: See page ...

41 Anchors PA/HPA Purlin Anchors Wood-to-concrete and -concrete block connectors that ... Purlin Anchor must hook around rebar. Wood splitting may occur when anchor is ... nailed to wood less than 3 wide. For widths less than ... is 5". Minimum concrete block left-to-right edge distance is 20". CONCRETE BLOCK ... Code Listing Key Chart. PA/HPA Purlin to Concrete Wall For I-Joist applications ... 8 and IBC 1620.2.1 state: ... Diaphragm to wall anchorage using embedded straps ... shall have the straps attached to or hooked around the reinforcing steel ... , or otherwise terminated to effectively transfer forces to the ... information. PA HPA35 PA/HPA Purlin to Concrete Block Wall ...

42 Anchors LSTHD/STHD Strap Tie Holdown Typical ... reduction. 4. Minimum nail end distance to prevent splitting is 10 x diameter, 1 ... be by Designer. 11. Loads shown apply to post tension slabs when one #4 rebar ( ... Application This product is preferable to similar connectors because of a) easier ... capacity and a staggered nail pattern to help minimize splitting. The latest ... movement during installation relative to the form. Allows for accurate location ... nailing pattern allows for nailing to the edges of double 2xs. A slot below ... line allows for increased front to back concrete bond and reduced spalling ... . Strap nail slots are countersunk to provide a lower nail head profile. Rim ... joist models accommodate up to a 17" clear span without any loss of ... one full cycle. Bending the strap 90 to aid wall placement may cause spalling ...

43 Anchors LSTHD/STHD Strap Tie Holdown SIMPSON ... costly retrofits. No additional labor to install. Holds STHD away from form ... Locator Line: Easy inspection to ensure proper location. Allows ... Diamond Hole: One more fastener to help prevent the STHD RJ models from ... MAY BE FOUNDATION REBAR) DOES NOT NEED TO BE TIED TO REBAR * CONCRETE FOUNDATION ... (bent one full cycle) for nailing to the stud, concrete spalling could ... . 4. It is the Designers responsibility to provide reinforcement to tie cold- ... joints and to resist bending stresses in the ... foundation due to anchor uplift. 5. Post design shall be ... sinkers 3185 POST-TENSION INFORMATION Top View of Post Tension Cable Placement ...

44 Anchors PA/PAHD/HPAHD Strap Tie Holdowns Wood- ... to-concrete connectors that satisfy engineering and ... holding device. Bending the strap 90 to aid wall placement may cause spalling ... less, measured from the embedment line to the bottom of the spall, full loads ... fasteners are used in the structural wood member, reduce loads according to the ... code. A wood splitting problem may occur when ... holdowns are nailed to lumber less than 3 wide. To lessen ... beneath, unless provisions are made to transfer the load, or the slab is ... designed to resist the load imposed by the anchor; ... over concrete block foundation walls. To get the full table load, the minimum ... center-to-center spacing is twice the embedment depth ... tension loads at the same time. To tie double 2x members together, the ...

Feature U.S. Patent 6,658,806 SM1 45 Anchors PA/PAHD/HPAHD Strap Tie Holdowns ... MAY BE FOUNDATION REBAR) DOES NOT NEED TO BE TIED TO REBAR * CONCRETE FOUNDATION ... , and then bent up vertically to attach to the stud. Load reduction may apply. ... Installation FEATURES Secures holdown to wood form-board. Allows for proper ... movement parallel and perpendicular to plate. Decreases possibility of ... misinstallation of strap to wood member. Simple to use: Common jobsite ... , and then bent up vertically to attach to the stud. Load reduction may apply. le ...

for short-term loading. 3. Specifier to design concrete for shear capacity. 4. ... ABU88R may be installed with 8-SDS X3 wood screws for the same table load. 5. For ... on column or concrete, according to the code. 6. HB dimension is the ... from the bottom of the post up to the first bolt hole. 7. NAILS: 16d 0. ... permanent structures that are exposed to the weather or water splash, or in ... do not provide adequate resistance to prevent members from rotating about the ... therefore are not recommended for non top-supported installations (such as fences or ... ABA, ABE and ABU for pre-pour installed anchors. For epoxy or wedge anchors, select and ... install according to anchor manufacturer's recommendations; ... Anchor Systems for tested, load-rated anchors and request T-ANCHORSPEC for more ...

lateral loads require the threaded rod to be set in wet concrete or attached to ... SET epoxy or AT adhesive. 3. Specifier to design concrete for shear capacity. 4. ... nail holes; only eight must be filled to achieve table loads. 3. Specifier to ... . See General Notes. Allows 1" to 2 clearance above concrete, 2" for ... do not provide adequate resistance to prevent members from rotating about the ... therefore are not recommended for non top-supported installations (such as fences or ... epoxy. Insert the EPB44T and adjust to the desired height. The threaded rod ... shall be embedded a minimum of 2 ". To adjust after the epoxy cures, drill a ... and rotate the post base up or down to the desired height. EPB44PHDG Drill a ... . Insert the EPB44PHDG and adjust to the desired height. The threaded rod ...

STEEL STRONG-WALL We have responded to the needs of builders, specifiers and ... . The result is the newest addition to the Strong-Wall line, our Steel Strong- ... allowable loads in the industry. Wood framing is preattached for interior and ... Stronger Wall: Allowable loads are two to three times higher than the original ... bolts and SDS screws. Easy access at top and bottom for quick installation. ... Contractor friendly: Easy to use reversible template for concrete ... ga FINISH: Vertical Panel Galvanized Top and Base Plates Simpson gray paint. NOW ... . Install Steel Strong-Wall flush to one face of framing and add furring to ... height between Steel Strong-Wall and top plates or header is using SDS x3 screws ... height, see ICC-ES ESR-1679. Attach to header or top plates with SDS x3 ...

93 3 4 " 12 80 3 4 W H T Qty of Top of Wall Screws 1 Anchor Bolt dia. (2 ... =4.4 per 1997 UBC. 4. Loads applicable to designs using the ASD alternate basic ... by 1.33. 5. Loads based on a 4000 lbs. total axial load acting on the entire panel ... combination with the shear load. Refer to ICC-ES ESR-1679 for corresponding shear ...

93 3 4 " 12 80 3 4 W H T Qty of Top of Wall Screws 1 Anchor Bolt dia. (2 ... designs using R=6.5 3. Loads applicable to designs using the ASD basic (Section ... . 4. Loads based on a 4000 lbs. total axial load acting on entire panel in ... for use in the State of Florida (refer to FL5113) 8. See page 61 for SSWAB anchor ...

(May be used for Steel Form Systems) TOP OF CONCRETE SSWTPF (Panel Form) 2" 1. ... increase and therefore are applicable to either the ASD Basic or Alternate ... increase and therefore are applicable to either the ASD Basic or Alternate ...

/4x36HS 36" 32" Model No. le Dia. Total Length SSWAB1x24 1" 24" 20" ... 1" 36" 32" Model No. le Dia. Total Length Foundation and stemwall design ... are for anchorage only. le 2" Heavy Top of Concrete Hex Nut fixed inplace on ... the and 1" diameters offer flexibility to meet specific project demands. ...

of the structure. Naming Scheme 8' to 10' SW24x8 Strong-Wall Width (in.) ... . Simply fasten the bottom of the wall to the embedded bolts with the provided ... hardware. The top of the wall attaches with pre-installed ... SDS screws to double top plates or can fasten to various header ... hardware is included. EASY TO INSTALL Reusable templates locate the ... the anchor bolts followed by a simple top and bottom plate attachment. Use 1 ... for nut. INSTALLATION GUIDE Attached to every wall. STATE-OF-THE-ART TESTING ... field representation available to assist you. NOTE: The Engineer of ... bolt nuts should be finger-tight plus to turn with a hand wrench, with ... consideration given to possible future wood shrinkage. Care should be taken to not ... over-torque the nut. Impact wrenches should not be ...

. 1. For plywood shear panel, add P to model name (e.g. SW24x8P), and multiply ... shim height between Strong-Wall and top plates or header is ". Shims of ... ) H (in) T (in) Number of Fasteners in Top of Wall Number of Fasteners in Bottom ... ) H (in) T (in) Number of Fasteners in Top of Wall Number of Fasteners in Bottom ... post. C3 Max. compressive force applied to top plates between studs. C4 Max. ... compressive force in end post due to load from above (C1) and overturning. ... allowable tension force in holdown due to net uplift. 1. For RF Raised Floor ... allowable vertical loads are intended to aid the user in correctly implementing ... structure. Load combinations that tend to cause compression can be limited by ... perpendicular to grain interface issues, by buckling of ...

/8" AB FOR 3x SILL SSTB28 OR SSTB34 5" TOP OF CONCRETE 5/8" AB FOR 3x SILL SSTB28 ... OR SSTB34 5" 1 OR 3" FOR -RF WALLS TOP OF CONCRETE 5/8" AB FOR 3x SILL SSTB28 ... of the template if the design is for a wood 1st floor or 2nd floor application. 4 ... Installation (Install with arrow on top of the bolt oriented as shown) Corner ... Installation (Install with arrow on top of the bolt oriented as shown) Non- ... (Bolt may be installed 45 to 135 as shown) Outer Edge of Concrete ...

H (in) T (in) Number of Fasteners in Top of Wall Allow. Shear V Load (lb) for ... V Load (lb/ft) Number of Mudsill Anchors 6 Holdown 2 Anchor Bolts Wall Weight ( ... 90 90 1. For plywood shear panel, add P to model name (e.g. SW24x8P), and ... walls with a header spanning over the top and connected as shown. 5. SW16 and ... . Larger headers may be required due to vertical loading. 8. Portal walls may ... in the Allowable Hole Chart attached to each wall ...

. 1. For plywood shear panel, add P to model name (e.g. SW24x8P), and ... 1 wall with a header spanning over the top and connected as shown. 5. Recommended ... . Larger headers may be required due to vertical loading. 7. Portal walls may ... (in) T (in) Number of Fasteners in Top of Wall Number of Mudsill Anchors 5 ... and Double Wall Garage Portal 1. Beam to support post and support post to ... . It is the designers responsibility to provide a complete load path for all ... that equivalent stiffness is equal to or greater than that provided by the ... by others) are minimum requirements to achieve the allowable loads. CODES: ... 1 Single Wall Garage Portal 1. Beam to support post and support post to ... . It is the designers responsibility to provide a complete load path for all ...

89 Engineered Wood Structural Composite Lumber Connectors ... . 45 o angle Nail at wrong angle Nail too long Use a 10dx1 nail (Simpson N10 HDG ... Hanger side flange supports joist top flange. Hangers provide some joist ... depth, attach staggered A34 framing anchors above the hanger. No Web Stiffener ... Hanger side flange is below the joist top flange. No web stiffener results in ... assemblies. Install with high-torque, low-speed drill (5 amp+). Do not over- ... C D 1.0. Increase as allowed per code to a maximum CD 1.33. This document uses ... 4", edge distance 1 ", spacing parallel to grain 4", spacing perpendicular to ... based on the capacity of the fasteners to transfer loads between plies. The ... adequate lateral bracing is provided to prevent displacement of the beam due to ...

118 Engineered Wood Structural Composite Lumber Connectors ... PAI/MPAI Purlin Anchors PAI PAI Purlin to Concrete Wall (MPAI similar) Model No. ... 2865 2865 1960 2355 2865 2865 Code Ref. Wood-to-concrete and -concrete block connectors that ... fastener holes. See General Notes. Wood splitting may occur when anchor is ... nailed to wood less than 3 wide. To reduce splitting for widths less than 3 ... on page 16-17.) PAI is designed for wood I-joists. Nail spacing is for 10dx1 ... nails 3" on center, to minimize the chance of wood splitting. ... is 5". Minimum concrete block left-to-right edge distance is 20". CONCRETE BLOCK ... .2.8 and IBC 1620.2.1 state: Diaphragm to wall anchorage using embedded straps ... shall have the straps attached to or hooked around the reinforcing steel ...

Connector This product is preferable to similar connectors because of a) easier ... STEP 1 Double angle cut the gable brace to sit flat on the wall double top plate ... against the gable end truss for 2x4 top plate. The double angle cuts should ... gable brace. STEP 2 Set each GBC on top of the double top plate so that the ... with the inside edge of the double top plate. Install fasteners into the top ... of the double top plate. STEP 3 Bend GBC legs (one time ... only) over the inside of the double top plate and install fasteners. STEP 4 ... the other end of the gable brace to blocking at the roof diaphragm as ... improved anchorage of gable bracing to the exterior wall. Installation ... . The GBC must be installed in pairs to achieve full load capacity. CODES: See ...

Fasteners Masonry Allowable Loads W H Top Face Joist Uplift (133 160) Download ( ... 100/115/125) 1 to 7 3 to 30 2-16d DPLX 2-10dx1 WMU 1 to 7 9 ... to 28 2-16d DPLX 4- x1 Titen 6-10dx1 625 ... construction. 2. Titen x1 installed on top of wall after grout has cured. 3. Mid- ... course above and below the hanger. 4. Top of Wall Installation. 5. NAILS: 16d ... WMU Mid-Wall Installation WMU Top of Wall Installation See pages 104-113 ... on pages 104-113; WM, WMI, WMU 12 ga. top flange and stirrup FINISH: Simpson gray ... nails must be installed into the top flange and embedded into the grouted ... course above and one course below the top flange with one #5 vertical rebar ... is 2000 psi. When installed on top of masonry wall, use 2-Titen x1 ... 131 Code Ref. 1.These loads also apply to masonry. 1" embed. table loads apply to ...

: These hangers are attached to grouted CMU walls using x 2 hex head ... not provided. Drill the diameter hole to the specified embedment depth plus ". ... Alternatively, drill the diameter hole to the specified embedment depth and blow ... the base material and will reduce the anchors load capacity. The hangers should be ...

for solid sawn, truss and engineered wood products. MATERIAL: 10 gauge FINISH: ... . All thread rods and/or machine bolts to be diameter x 4 long, grade A307 or ... better. 6.Additional anchorage products to be designed by others. 7.Uplift loads ... 1 Joist (133) (160) (133) (160) Top Face MBHA 1-ATR x8 1-ATR x 8 18-10d ... . All thread rods and/or machine bolts to be diameter x 8" long, grade A307 or ... better. Refer to the Anchoring Systems catalog. 1. ...

series provides an engineered method to properly attach roof trusses to ... . Information regarding the use of two anchors on single- and multi-ply trusses is ... TSS moisture barrier may be preattached to the truss using 6d commons. CODES: See ... increase on the steel capacity. Refer to page 13 for further explanation. 2.Five ... the truss seat of the HETAL. 3.Parallel-to-plate load towards face of HETAL is 1975 lbs ... , HETA20 and HHETA20, it is acceptable to use a reduced number of fasteners ... for full load. 8. See instruction to the Designer page 15 for loads in ... /HETA/HHETA/HETAL/TSS Embedded Truss Anchors and Truss Seat Snap-In ...

/HETA/HHETA/HETAL/TSS Embedded Truss Anchors and Truss Seat Snap-In 1. For concrete ... 35% and the HETA load 8%. 2. Divide total number of fasteners equally between ... fc is 2,500 psi. 4. See instruction to the Designer page 15 for loads in ... increase on the steel capacity. Refer to page 13 for further explanation. 7. ... and MSTCM models are designed for wood to masonry applications. The MSTC ... fasteners. See General Notes. Attach to grouted concrete block. CODES: See page ... . Model No. Ga Dimensions Fasteners (Total) Allowable Tension Loads W L Nails CMU ... increase on the steel capacity. Refer to page 13 for further explanation. 2. ... MSTCM40 Model No. Clear Span Fasteners (Total) Allowable Tension Loads Nails CMU (133 ... - x1 Titen (DF/SP) SPF/HF MSTAM36 Floor-to-Floor Clear Span Table Available with ...

1,2 Spruce-Pine-Fir Allowable Loads 1,2 To Rafters/ Truss To CMU Uplift 4 Lateral ... 3 2-10dx1 18 H16-2S 6x2 Titen To Concrete 3 18 3 11 Code Ref 125 ... Presloped at 5:12. Pitch of 3:12 to 7:12 is acceptable H16 (H16-2 similar ... ) 3 HM9 Attaching Truss to Masonry 1 H16S Installed into Masonry ... of 2 must be used when framing anchors are installed on each side of the joist ... into Masonry The HM9 is designed to retrofit roof truss/rafters for block ... provides for various truss heightup to a maximum of 13 ". Minimum heel height ... do not replace solid blocking. Attach to grouted concrete block with a minimum ... one #5 rebar horizontal in the top lintel block. CODES: See page 12 for ...

LGT2 Model No. W O.C. Dim Between Anchors Fasteners DF/SP Allowable Uplift Loads ... 9250 9250 Model No. W O.C. Dim Between Anchors Fasteners DF/SP Allowable Uplift Loads ... provides high uplift resistance for wood frame and concrete block construction ... be installed on trusses and beams with top chord slopes from 3:12 to 8:12. ... or beam, shimming is required. Fasten to act as one unit. Attach to grouted ... minimum one #5 rebar horizontal in the top lintel block. Minimum f I c = 2500 psi ... maximum aggregate ". See page 167 for wood applications. CODES: See page 12 for ... . 1. Attached members must be designed to resist applied loads. 2. To achieve the ... shall be designed by the Designer. 3. To achieve the loads listed for the MGT ... Vertical reinforcement may be required to transfer the loads per Designer. 4. ...

washer required NEW! As an alternative to coil strap, our new FSC-Floor Span ... Connector, connects upper floors to lower floors from the inside of the ... the FSC. Use threaded rod between 4' to 5' long, grade A307 or better, with ... maybe installed off the sill plate up to 18". Drill to diameter hole through the ... attachment. Nails can be installed up to 30 degree angle with no reduction in ... reduce the capacity of the connection. To calculate a reduced capacity use 129 lb ... MSTC66B3 installed over sheathing up to thick achieve 0.85 of table loads. 5. ... .125" deflection from static tests on wood members, steel ultimate divided by 2, ... MSTC66B3 are pre-bent straps designed to transfer tension load from an upper ... story shearwall to a beam on the story below. MATERIAL: ...

160 Straps Ties FTA/LFTA Floor Tie Anchors T and L Strap Ties Typical L ... Designed for use as a floor-to-floor tension tie, one FTA replaces two ... between floors allow preattachment to the joist during installation; these ... s clear span of 17" will accommodate up to a 12" joist. The clear span of the FTA ... . Model No. Ga Dimensions Fasteners (Total) Allowable Uplift Loads 1 (133) ... allowable load for the LFTA according to the code when nails penetrate wood less ... . 1212HL, 1616HL, 1212HT and 1616HT are to be installed in pairs with machine ...

H2.5 Installation (Nails into both top plates) H3 Installation (Nails into ... upper top plate) H4 Installation (Nails into ... upper top plate) H5 Installation (Nails into both ... top plates) H6 Stud to Top Plate Installation 9 8 7 1 10 H5A ... Installation (Nails into both top plates) 11 12 2 3 H2.5A Installation ( ... Nails into both top plates) 4 H2.5T Installation (Nails ... into both top plates) 5 H6 Stud to Band Joist Installation 13 1. Loads ... of 2 must be used when framing anchors are installed on each side of the ... .5A). 3. Allowable uplift load for stud to bottom plate installation is 400 lbs ( ... in the F 1 direction are not intended to replace diaphragm boundary members or ... in the same area (i.e. truss to plate and plate to stud) must be on ...

with HTT22s Install two LBP washers on top of each crescent washer (total four ... washers) for wood installation. All washers and crescent ... .5 LGT2 Model No. W O.C. Dim. Between Anchors Fasteners Doug-Fir- Larch/ So. Pine ... Allowable Uplift Loads (133/160) Nails to Studs or Anchor Diameter Girder Code ... 1. Attached members must be designed to resist applied loads. 2. HGT additional ... anchorage products to be designed by others. 3. Allowable ... all specified nails are installed to either a solid header or minimum double ... 2x6 web. 7. Refer to T-HTIEBEARING for LGT allowable bearing ... load capacity. Low profile connection to studs ensures easy installation of ... drywall. Simple to install and can be installed on the ... provides high uplift resistance for wood frame and concrete block construction ...

loads are for one anchor. When anchors are installed on each side of the joist ... cross-grain tension or bending of the wood during loading if not reinforced ... LTP5 may be installed over sheathing up to thick with no reduction in load when ... . The larger LTP5 spans subfloor at the top of the blocking or rim joist. The ... Tie Plate transfers shear forces for top plate-to-rim joist or blocking ... connections. Nail holes are spaced to prevent wood splitting for single and ... double top plate applications. May be installed ... over plywood sheathing. The A35 anchors exclusive bending slot allows instant ... reversible design permits the A35 to secure a great variety of connections ... Listing Key Chart. A35 LTP5 A34 Joists to Plate with A Leg Inside 2 A35 1 A34 ... Ceiling Joists to Beam 5 LTP4 Installed over Plywood ...

loads are for one anchor attached to blocking minimum 1 thick. 2.RBC can be ... installed with up to gap and achieve 100% of the listed load ... other loads govern. 4.When attaching to concrete use 3- x1 Titens. 5.RBC ... of 395 lb. (133/160%) in a parallel to wall (F 1) load direction for Douglas ... -Fir-Larch/ So. Pine Allowable Loads To Plate To Blocking Lateral (133/160) ... Loads Lateral (133/160) 1 45 to 90 440 6-10dx1 6-10dx1 6-10dx1 6- ... 10dx1 3- "x2 Titen 6-10dx1 380 2 0 to 30 485 420 160 3 0 to 45 350 350 ... Fasteners 4 Typical RBC Installation to CMU Block 3 2 Typical RBC Installation ... The RBC Roof Boundary Clip is designed to aid installation and transfer shear ... between the roof diaphragm and wall top plates. The locator tabs make proper ... the clip easy. The RBC can be used on wood or masonry walls and will handle roof ...

ICFVL Ledger Connector System Dia. Anchors at Dia. Anchors at Ledger Type 12" o.c ... /SPF 48 48 43 48 48 48 (2)- Dia. Anchors at 12" o.c. 24" o.c. 36" o.c. 48" o.c. ... 21 42 48 48 Dia. Anchors at 12" o.c. 24" o.c. 36" o.c. 48" o.c. ... (0.054") Connector Type ICFVL SPACING TO REPLACE ANCHOR BOLTS (in.) 1,2,3 ICFVL ... ICFVL ICFVL 45 48 12 24 36 48 Code Ref. WOOD LEDGERS STEEL LEDGERS NEW! The ICFVL ... Ledger Connector System is engineered to solve the challenges of mounting wood ... or steel ledgers to insulated concrete form (ICF) walls. ... of the system, the ICFVL, is designed to provide both vertical and lateral, in- ... is still quick, versatile and easy to use but now provides so much more! ... and the hole allows for concrete to flow through and around the connector. ...

PGT1.5-R similar) U.S. Patent 5,297,890 Top View 45 Corner Installation Termination ... Top View Typical PGT2Z-R Fence Installation ... Typical PGTIC2Z-R Fence Installation Top View 90 Corner Installation The PGTIC2Z ... splices and uneven terrain, replacing wood posts. The PGT1.5Z-R is for 1 pipe (1 ... . See General Notes. PGTIC2Z-R to Post Install two set screws (supplied ... socket in predrilled holes. PGTIC2Z-R to Rails Use SDS x1 wood screws (not ... on vertical pipes, offsetting corners to allow for the correct rail alignment. ... Use 3 to 4 PGTs per pipe; line up to stringline. Fasten PGT with hex head ... bolt (supplied). PGT attaches to rails with four SDS x1 HDG wood screws ... for predrilling. Nail fence boards to rails. PGTIC2Z-R Typical DJT14Z ... over unstable soil or water. Minimize wood splitting by flattening nail points or ...

based on round "Viga" (Ponderosa Pine) wood posts. 2. All allowable uplift loads ... factor of 4. Concrete anchorage to be designed by others, refer to ... except the PBV, which is based on the wood bearing strength (700 psi for ... . Model No. Ga Dimensions Bolts (Total) Allowable Loads 1,2,3,4 W1 W2 L D1 D2 ... black paint, gray paint or galvanized TO ORDER: All products with PC suffix are ... paint. OPTIONS: Gussets may be added to HL models when L 5". Specify G after ... be centered on the face of the member to which they are attached. 4. Wood ... and thickness of 3 for table loads to apply. 5. Wood members for the 4 and 7 ... and thickness of 5 for table loads to apply. 6. For Uplift loads, parts must ... Insert all-thread rod and allow epoxy to set and cure. Secure standoff to post ...

194 Wood Construction Connectors CONTINUOUS LOAD ... TYPICAL ROOF CONNECTIONS Pages 162 to 168 TYPICAL FLOOR-TO-FLOOR CONNECTIONS ... Pages 35 to 45, 155 to 160 TYPICAL FOUNDATION CONNECTIONS ... Pages 23 to 34 This drawing shows the connection ... load transfer path from the rafters to the foundation of a two-story house. ... of creating a structure better able to withstand the forces of mother nature ... considered an engineered system. Refer to the page numbers for the full range ... . Consult a qualified Designer to ensure that correct connector ... and installation methods are used to achieve the full design load values. ... values for adhesive and mechanical anchors, PAT and carbide drill bits. A binder ... Tiedown Systems This System is designed to provide the over-turning holdown ...

22035 W. Valley Highway Kent, WA 98032 Toll Free: 877/564-2041 Eastern Canada 5 ... first building products manufacturer to become a sponsor of the NAHB Research ... training materials and assistance to participating Builders and Trade ... representative or call 800-999-5099 to learn more. www.builtnoequal.com Every ... day we work hard to earn your business, blending the ... quality of our products and services to exceed your expectations. This is our ... pledge to you ...