E-Mail pwdco@pwdahl.com PWDCO DC Filter CapacitorList 2 PWDCO Air Variable Capacitor ... List 5 PWDCO Vacuum CapacitorList 11 PWDCO RF Transmitting Capacitor ... List 31 PWDCO Transient Suppressor List 39 PWDCO RF Inductor List 41 PWDCO ... Fans Blower List 46 PWDCO Power Resistor List 48 ... PWDCO Diodes Rectifier List 53 PWDCO Vacuum Relay List 56 PWDCO ... RF Plate Filament Choke List 65 PWDCO Constant Voltage Transformer ... List 66 PWDCO Variable Transformer List 67 PWDCO Tube Socket List 69 PWDCO ... Power Supply List 70 PWDCO Electronic RF Connector List ... PWDCO Miscellaneous Stock Transformer list 74 PWDCO Miscellaneous Stock Reactor ... List 80 PWDCO Panel Meter List 81 PWDCO Electron Tube List 99 ...
2
PWDCO DC FILTER CAPACITORLIST AS OF 07/08/05 CELIC500 CAP, ... 750 MFD 165 WVDC COMPUTER GRADE FILTER CAPACITOR SPRAGUE P/N 761A954-PT5 H 4.375 W 2. ... 2500 MFD 80 WVDC COMPUTER GRADE CAPACITOR MALLORY P/N 2020408 H 4.500 W 2.000 D ...
the specified tolerance solder the capacitor to the test jig glass epoxy board in ... under the same conditions as 10 the capacitor should be subjected to a simple ... directions total of 6 hours solder the capacitor to the test jig glass epoxy boards ... evenly and continuously immerse the capacitor in a solution of ethanol jis-k-8101 and ... nominal capacitance pf 5 2 preheat the capacitor at 120 to 150d for 1 minute immerse the ... capacitor in a eutectic solder or sn-3.0ag-0.5cu ... 24t2 hours 15 temperature cycle fix the capacitor to the supporting jig in the same ... according to the four heat treatments listed in the following table let sit for 24t2 ... 30t3 2 to 3 30t3 2 to 3 step c let the capacitor sit at 40t2d and 90 to 95 humidity for ...
59
pf r7 r6 within t7.5 fix the capacitor to the supporting jig in the same ... according to the four heat treatments listed in the following table let sit for 24t2 ... measurement r7 r6 within t12.5 sit the capacitor at 40t2°c and 90 to 95 humidity for ...
0.03 max w.v 16v 0.05 max 1 fix the capacitor to the supporting jig in the same ... according to the four heat treatments listed in the following table let sit for 24±2 ... 150+3 0 l8/r9/5g temp 1 15±3 1 sit the capacitor for 1000±12 hours at 150±3°c let sit ...
16
type high dielectric type fix the capacitor to the supporting jig in the same ... according to the two heat treatments listed in the following table maximum transfer ... 4 hours after preheating immerse the capacitor in a solution of ethanol jis-k-8101 and ... 15 minutes after preheating immerse the capacitor in a solution of ethanol jis-k-8101 and ... 15 minutes after preheating immerse the capacitor in a solution of ethanol jis-k-8101 and ...
condition 1 do not use the trimmer capacitor under atmosphere of rtv silicone rubber ... silicone sealant 2 before using trimmer capacitor please store under the condition of -10 ... sunlight 6 do not use the trimmer capacitor under the conditions listed below 1 ...
12
condition 1 do not use the trimmer capacitor under atmosphere of rtv silicone rubber ... silicone sealant 2 before using trimmer capacitor please store under the condition of -10 ... sunlight 6 do not use the trimmer capacitor under the conditions listed below 1 ... /or excessive temperature the trimmer capacitor may deviate from the specified ... the monolithic stator of the trimmer capacitor if such contact does occur the trimmer ... capacitor may be damaged 6 our recommended ... to prevent the deterioration of trimmer capacitor characteristics apply flux only to ... 5.0 n [ref 500gf max when the trimmer capacitor is mounted on the pcb 2 do not warp and ... /or bend pcb to prevent trimmer capacitor from breakage 3 use the suitable ... other note the polarity of the trimmer capacitor to minimize influence by stray ...
capacitance of products in the parts list when it is required for applying safety ... capacitance of products in the parts list when it is required for applying safety ...
8
capacitance of products in the parts list when it is required for applying safety ...
and poor wire bonding 1 store the capacitors in manufacturer s package in the ... 30 to 70%rh 2 avoid storing the capacitors in the following conditions a ambient ... soldering and mounting 1 die bonding of capacitors 1 using materials and bonding ... atmosphere 2 notice a please scrub the capacitors while mounting b die bonding condition ... in other bonding conditions not listed above s notice handling do not directly ... touch capacitors with hand to prevent poor die bonding ...
16
in this catalog for the applications listed below which require especially high ... requirements to the applications listed in the above 3 product specifications ...
test method the terminal of a capacitor is dipped into a solution of ethanol ... according to the 4 heat treatments listed in the following table next repeat ... of salt at 0t3°c for 15 min the capacitor is then promptly washed in running ... min cu0.01µf 10m · µf min set the capacitor at 40t2°c and relative humidity of 90 ... for 24t2 hrs at room temperature the capacitor should be fully immersed unagitated in ... gently marking on the surface of the capacitor should immediately be visually examined ...
29
in this catalog for the applications listed below which require especially high ... requirements to the applications listed above 3 product specifications in this ...
in this catalog for the applications listed below which require especially high ... requirements to the applications listed in the above 3 product specifications ...
in this catalog for the applications listed below which require especially high ... requirements to the applications listed in the above 3 product specifications ...
