rolling motors das ii tube rolling system das- ... 100-trs benchtop tube rolling system models 1850 chucks ... and adapters condenser tube expanders introduction ... g-900 series tube expanders g-1300 series tube ... expanders g-800 series tube expanders g-800 series five- ... roll tube expanders g-1200 series tube expanders g-1200 series five- ... roll tube expanders g-8012 series tube expanders special tube expanders ... 15 19 20 21 25 27 31 33 35 tube installation tools heat exchanger ... accessories drills tube end facers beadind tools belling tools ... flaring tools mandrel extensions universal ... one piece tube plugs brass steel 316 ss 304 ss 416 ss ... aluminum monel two piece brass tube plugs ...
19
series heat exchanger and condenser tube expanders tube sheet thickness 1/2 in ... to 4 in 12.7 mm to 101.6 mm tube o.d tube gauge in mm tube i.d in mm in mm bwg ... stock no roll set no stock no special tube expanders min i.d tool enters in mm max ... 140 54.3 2.407 61.1 m-93 2542400 linsen flaring expander this special expander enlarges ... and aluminum tubing so that another tube of the same size may be inserted into ... expanders are ideally suited for faster tube rolling in thick tube sheets the ... without removing the expander from the tube step rolling expanders are available in ... throughout the full thickness of the tube sheet 8012-2-3/4-10-16 5140500 r-66 ... the mandrel allows full expansion of a tube with minimum travel of the mandrel the ... length and to allow use near sharp tube bends or tube inserts collins expander ...
gaugeable tube fittings and adapter fittings 19 ... connectors f flat 37° e s a an fitting tube od 1/16 1/8 1/4 5/16 3/8 1/2 3/4 1 an ... tube flare size 1/8 1/8 1/4 1/4 5/16 1/4 3/8 ... fitting f flat f flat 37° e s a an tubetube flare od size 1/4 3/8 1/2 3/4 1 1/ ...
45
gaugeable tube fittings and adapter fittings 45 tube ... thread boss sae/ms straight thread st tube od 1/8 1/4 3/8 1/2 5/8 3/4 1 1 1/4 1 1/ ... 1/8 2 3/4 o-seal sae/ms straight thread tube od 1/8 3/16 1/4 5/16 3/8 1/2 sae/ms ... ferrules f flat 37° e a an thread an tube flare size 1/4 1/4 3/8 1/2 3/4 1 basic ... 5/16-12unj-3 -16-ta-1-16an thread size tube od 1/4 3/8 1/2 3/4 1 dimensions a 1.46 ...
compression sleeve principle nta nylon tube air brake fittings provide a d.o.t ... fitting contains a staked-in stainless tube insert to prevent tube restriction when ... inserts flare fittings 45° sae flared tube fitting connections are made by ... slipping the nut over the tubing and flaring the end of the tubing by use of a ... flaring tool when used with rubber hose ... /8 and 3/16 sizes are pre-assembled the tube support is built into the fitting body ... on tube sizes larger than 3/16 so there is no ...
299
t1 male orb connector to 37° flare part tube thread o-ring pkg no o.d size thread ... 90° adjustable elbow orb to 37° flare tube o-ring part tube thread thread pkg no o ...
INCHES CPI A-LOK CHANGES FLARE TUBE W PART NO. PART NO. WITH END O.D ... INCHES CPI A-LOK CHANGES FLARE TUBE W PART NO. PART NO. WITH END O.D ... INTER- INCHES CPI A-LOK CHANGES TUBE W PART NO. PART NO. WITH O.D. D ... (AN) to CPI /A-LOK For fractional tube XHBZ, XASC 37 Flare Connector For ... fractional tube D W HEX D A B C W HEX Dimensions for ... Bulkhead Connector For fractional tube D A B C L W HEX NOTE: A and C ...
tee fitting to join two 3/8 45° flared tubes to 1/4 male pipe thread cadmium plated ... -577417 j-7235 j-7235-1 1/4 pipe to 3/8 tube union 5/16-24 ball stud 5/16-24 ball ...
tee fitting to join two 3/8 45° flared tubes to 1/4 male pipe thread cadmium plated ... -577417 j-7235 j-7235-1 1/4 pipe to 3/8 tube union 5/16-24 ball stud 5/16-24 ball ...
tee fitting to join two 3/8 45° flared tubes to 1/4 male pipe thread cadmium plated ... -577417 j-7235 j-7235-1 1/4 pipe to 3/8 tube union 5/16-24 ball stud 5/16-24 ball ...
